Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2016.05
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292096 AUTOMATIC TRANSAXLE SYSTEM C

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in the lock-up condition when the brakes are suddenly applied.

When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.

DTC No. DTC Detection Condition Trouble Area
P0724 Stop light switch remains ON even when vehicle is driven in GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic)
·

Short in stop light switch signal circuit

·

Stop light switch

·

ECM



MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains ON. When the stop light switch remains ON during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC. The vehicle must GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) 5 times for 2 driving cycles in order for the DTC to be output.

WIRING DIAGRAM

C355895E03
0.865,1.698 1.49,1.948 0.625,0.25 10 false Battery 2.052,1.188 2.677,1.438 0.625,0.25 10 false ALT 1.063,1.188 1.688,1.438 0.625,0.25 10 false FL MAIN 2.656,1.188 3.625,1.438 0.969,0.25 10 false RH-MAIN-JB 3.781,1.188 4.406,1.438 0.625,0.25 10 false STOP 4.521,1.313 5.146,1.563 0.625,0.25 10 false A37 5.948,1 6.573,1.25 0.625,0.25 10 false STP 5.146,1 5.771,1.25 0.625,0.25 10 false OUT 4.656,0.99 5.281,1.24 0.625,0.25 10 false +B 5.688,0.896 6.313,1.146 0.625,0.25 10 false 36 5.51,0.906 6.135,1.156 0.625,0.25 10 false 2 4.479,0.906 5.104,1.156 0.625,0.25 10 false 1 4.521,1.5 5.698,1.875 1.177,0.375 10 false Stop Light Switch Assembly 6.156,2.344 6.573,2.583 0.417,0.24 10 false ECM 6.156,2.167 6.573,2.406 0.417,0.24 10 false A7

CAUTION / NOTICE / HINT

HINT:

Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the intelligent tester to the DLC3.

4.

Turn the ignition switch on (IG) and turn the tester ON.

5.

Enter the following menus: Powertrain / Engine and ECT / Data List.

6.

Follow the instructions on the tester and read the Data List.


ECM:
Item Measurement Item/
Range (Display)
Normal Condition Diagnostic Note
Stop Light Switch Stop light switch status/
ON or OFF
·

Brake pedal is depressed: ON

·

Brake pedal is released: OFF


-

PROCEDURE

1.INSPECT STOP LIGHT SWITCH
a.

Inspect the stop light switch assembly (See page Vehicle Interior>LIGHTING>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).



OK

2.CHECK WIRE HARNESS (ECM - BATTERY)

NG

REPLACE STOP LIGHT SWITCH

2.CHECK WIRE HARNESS (ECM - BATTERY)
U188285E02
1.865,1.99 2.073,2.635 true 0.156,0.052 1.563,0.219 1.406,0.167 10 false Wire Harness Side: 1.948,2.667 2.24,2.875 0.292,0.208 10 false STP 1.542,0.896 1.917,1.125 0.375,0.229 10 false A7

a.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
A7-36 (STP) - Body ground Brake pedal is depressed 10 to 14 V
A7-36 (STP) - Body ground Brake pedal is released Below 1 V




OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR