Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292096 AUTOMATIC TRANSAXLE SYSTEM C

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P2769  Torque Converter Clutch Solenoid Circuit Low (Shift Solenoid Valve DSL)  P2770  Torque Converter Clutch Solenoid Circuit High (Shift Solenoid Valve DSL)  


DESCRIPTION

The shift solenoid valve DSL is turned ON and OFF by signals from the ECM to control the hydraulic pressure acting on the lock-up relay valve, which then controls operation of the lock-up clutch.

DTC No. DTC Detection Condition Trouble Area
P2769 ECM detects short in shift solenoid valve DSL circuit when shift solenoid valve DSL is operated (2 trip detection logic)
·

Short in shift solenoid valve DSL circuit

·

Shift solenoid valve DSL

·

ECM


P2770 ECM detects open in shift solenoid valve DSL circuit when shift solenoid valve DSL is not operated (2 trip detection logic)
·

Open in shift solenoid valve DSL circuit

·

Shift solenoid valve DSL

·

ECM



Fail-safe function:

If the ECM detects a malfunction, it turns the shift solenoid valve DSL OFF.

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the ECM based on engine rpm, engine load, engine temperature, vehicle speed, transmission temperature, and shift position selection. The ECM determines the lock-up status of the torque converter by comparing the engine rpm (NE) to the input rpm (NT). The ECM calculates the actual transmission gear by comparing the input rpm (NT) to the output rpm (SP2). When conditions are appropriate, the ECM requests "lock-up" by applying control voltage to the shift solenoid valve DSL. When the shift solenoid valve DSL is opened, the shift solenoid valve DSL applies pressure to the lock-up relay valve and locks the torque converter assembly. If the ECM detects an open or short in the shift solenoid valve DSL circuit, the ECM interprets this as a fault in the shift solenoid valve DSL or its circuit. The ECM will illuminate the MIL and store a DTC.

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE DSL)
a.
C141259E12
1.729,0.979 1.875,0.521 false 1.771,0.354 2.135,0.552 0.365,0.198 10 false DSL

Disconnect the D51 wire connector.


b.

Measure the resistance of the transmission wire.

Standard resistance:
Tester Connection Condition Specified Condition
3 (DSL) - Body ground 20°C (68°F) 11 to 13 Ω




OK

2.CHECK WIRE HARNESS (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE DSL
2.CHECK WIRE HARNESS (TRANSMISSION WIRE - ECM)
a.
U189342E02
1.823,1.969 2.031,2.604 true 1.552,0.948 1.927,1.177 0.375,0.229 10 false D2 1.938,2.635 2.344,2.833 0.406,0.198 10 false DSL 0.135,0.094 1.563,0.26 1.427,0.167 10 false Wire Harness Side:

Disconnect the D2 ECM connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
D2-79 (DSL) - Body ground 20°C (68°F) 11 to 13 Ω




OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE DSL
a.

Remove the shift solenoid valve DSL.


A112706E01
1.27,2.578 1.524,2.787 0.255,0.209 10 (-) 1.931,2.578 2.185,2.787 0.255,0.209 10 (+)

b.

Measure the resistance between the solenoid valve terminal and solenoid valve body.

Standard resistance:

11 to 13 Ω at 20°C (68°F)



c.

Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.

OK:

Valve moves and makes operating noise.




OK

REPAIR OR REPLACE TRANSMISSION WIRE

NG

REPLACE SHIFT SOLENOID VALVE DSL