Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292096 AUTOMATIC TRANSAXLE SYSTEM D

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  DIAGNOSIS SYSTEM  


EURO-OBD


a.

When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to an OBD scan tool (complying with ISO 15765-4). Various data output from the vehicle's ECM can then be read.


b.
C140836

Euro-OBD regulations require that the vehicle's on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:

i.

The emission control system/components.


ii.

The powertrain control components (which affect vehicle emissions).


iii.

The computer.

In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are recorded in the ECM memory.

If the malfunction does not reoccur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.



c.
B135940E01
0.425,2.845 1.557,3.021 1.132,0.177 10 Intelligent Tester 0.6,2.589 0.6,2.832 false 1.48,2.058 1.864,2.214 0.385,0.156 10 DLC3 1.717,2.051 1.841,1.732 false

To check DTCs, connect the intelligent tester to the Data Link Connector 3 (DLC3) of the vehicle. The tester displays DTCs, freeze frame data and a variety of engine data.

The DTCs and freeze frame data can be erased with the tester (see page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR).



M-OBD (Except European spec.)


a.

When troubleshooting Multiplex On-Board Diagnostic (M-OBD) vehicles, the vehicle must be connected to the intelligent tester. Various data output from the ECM can then be read.


b.
C140836

OBD regulations require that the vehicle's on-board computer illuminate the MIL on the instrument panel when the computer detects a malfunction in:

i.

The emission control system/components.


ii.

The powertrain control components (which affect vehicle emissions).


iii.

The computer.

In addition, the applicable DTCs are recorded in the ECM memory.

If the malfunction does not reoccur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.




NORMAL MODE AND CHECK MODE


a.

The diagnosis system operates in "Normal mode" during normal vehicle use. In normal mode, "2 trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1 trip detection logic" is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent malfunctions.



2 TRIP DETECTION LOGIC


a.

When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next drive cycle, the MIL is illuminated (2nd trip).



FREEZE FRAME DATA


a.

Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


b.
C140837E69
0.375,1.729 2.813,1.979 2.438,0.25 10 false Freeze frame data which can be read 0.688,0.688 1.313,0.885 0.625,0.198 10 false 0.5 sec. 1.323,0.688 1.948,0.885 0.625,0.198 10 false 0.5 sec. 1.958,0.688 2.583,0.885 0.625,0.198 10 false 0.5 sec. 1.833,0.125 2.885,0.417 1.052,0.292 10 false DTC was set

The intelligent tester records freeze frame data in 5 different instances: 1) 3 times before the DTC is set, 2) once when the DTC is set, and 3) once after the DTC is set. These data can be used to simulate the vehicle's condition around the time when the malfunction occurred. The data may help find the cause of the malfunction, or judge if the DTC is being caused by a temporary malfunction or not.



DATA LINK CONNECTOR 3 (DLC3)


a.
C140838E20
2.354,1.521 2.438,1.865 false 1.99,1.521 1.917,1.875 false 2.708,0.583 2.188,1 false 2.135,0.583 2,1 false 1.698,0.594 1.792,1 false 1.313,0.594 1.604,1.01 false 2.344,1.885 2.75,2.083 0.406,0.198 10 false BAT 1.708,1.885 2.115,2.083 0.406,0.198 10 false CANL 2.74,0.458 3.146,0.656 0.406,0.198 10 false SIL 1.969,0.417 2.521,0.615 0.552,0.198 10 false CANH 1.563,0.427 1.969,0.625 0.406,0.198 10 false SG 1.51,0.063 1.917,0.26 0.406,0.198 10 false DLC3 1.177,0.427 1.583,0.625 0.406,0.198 10 false CG

The vehicle's ECM uses the ISO 15765-4 for communication protocol. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.

Terminal of DLC3:
Symbols (Terminal No.) Terminal Description Condition Specified Condition
SIL (7) - SG (5) Bus "+" line During transmission Pulse generation
CG (4) - Body ground Chassis ground Always Below 1 Ω
SG (5) - Body ground Signal ground Always Below 1 Ω
BAT (16) - Body ground Battery positive Always 9 to 14 V
CANH (6) - CANL (14) CAN bus line Ignition switch off* 54 to 69 Ω
CANH (6) - Battery positive HIGH-level CAN bus line Ignition switch off* 6 kΩ or higher
CANH (6) - CG (4) HIGH-level CAN bus line Ignition switch off* 200 Ω or higher
CANL (14) - Battery positive LOW-level CAN bus line Ignition switch off* 6 kΩ or higher
CANL (14) - CG (4) LOW-level CAN bus line Ignition switch off* 200 Ω or higher



NOTICE:

*: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.


If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.

HINT:

Connect the cable of the intelligent tester to the DLC3, turn the ignition switch on (IG) and attempt to use the tester. If the screen displays UNABLE TO CONNECT TO VEHICLE, a problem exists in the vehicle side or the tester side.


If communication is normal when the tester is connected to another vehicle, inspect the DLC3 on the original vehicle.

If communication is still not possible when the tester is connected to another vehicle, the problem is probably in the tester itself. Consult the Service Department listed in the tester's instruction manual.

CHECK MIL


a.

Check that the MIL illuminates when turning the ignition switch on (IG).

If the MIL does not illuminate, there is a problem in the MIL circuit (see page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>MIL Circuit).


b.

When the engine is started, the MIL should turn off.