Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0715  Input / Turbine Speed Sensor Circuit Malfunction  P0717  Input Speed Sensor Circuit No Signal  


SYSTEM DESCRIPTION

This sensor detects the rotation speed of the turbine which shows the input revolution of the transaxle. By comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (NC), the TCM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, thus, providing smooth gear shifts.

C133216E01
1.329,0.443 2.200,0.599 0.871,0.156 10 Counter Gear 4.618,0.419 5.426,0.582 0.809,0.163 10 Clutch Drum 1.01,3.235 2.619,3.384 1.609,0.149 10 Output Speed Sensor NC 4.145,3.196 5.636,3.345 1.491,0.149 10 Input Speed Sensor NT 3.157,1.769 2.453,0.534 2.453,0.534 2.232,0.534 false 4.075,1.685 4.453,0.499 4.453,0.499 4.579,0.499 false 3.681,2.657 3.991,3.266 3.991,3.266 4.11,3.266 false 3.157,2.385 2.737,3.315 2.737,3.315 2.632,3.315 false

DTC No. DTC Detection Condition Trouble Area
P0715 When the speed sensor input voltage is either more than 1.9 V or less than 0.1 V for 4.5 seconds or more.
·

Transmission revolution sensor (speed sensor NT)

·

TCM


P0717 ECM detects conditions (a), (b) and (c) continuously for 5 sec. or more (1-trip detection logic):
(a) Vehicle speed: 31 mph (50 km/h) or more.
(b) Park/neutral position switch (STAR and R): OFF.
(c) Speed sensor (NT): less than 300 rpm.

MONITOR DESCRIPTION

The NT terminal of the TCM detects a revolution signal from the speed sensor (NT) (input RPM). The TCM calculates a gearshift comparing the speed sensor (NT) with the speed sensor (NC).

While the vehicle is operating in 2nd, 3rd, 4th or 5th gear in the D position, if the input shaft revolution is less than 300 rpm *1 although the output shaft revolution is more than 1,000 rpm*2, the TCM interprets this as a fault, illuminates the MIL and stores the DTC.

*1: Pulse is not output or is irregularly output.

*2: The vehicle speed is 50 km/h (31 mph) or more.

WIRING DIAGRAM

C133260E40
5.094,2.229 5.635,2.406 0.542,0.177 10 false NTB 5.083,2.708 5.625,2.885 0.542,0.177 10 false NTO 5.635,0.521 6.031,0.917 0.396,0.396 10 false TCM 1,3.333 2.302,3.719 1.302,0.385 10 false Speed Sensor (NT) 2.198,3.875 3.521,4.073 1.323,0.198 10 false Transaxle Assembly 4.865,2.115 5.021,2.292 0.156,0.177 10 false 1 4.865,2.594 5.021,2.771 0.156,0.177 10 false 2 2.031,2.125 2.188,2.302 0.156,0.177 10 false 1 2.042,2.594 2.198,2.771 0.156,0.177 10 false 2 1.646,2.604 1.927,2.76 0.281,0.156 10 true NTO 1.646,2.125 1.948,2.292 0.302,0.167 10 true NTB

CAUTION / NOTICE / HINT

DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty.


HINT:

According to the Data List displayed on the intelligent tester, you can read the value of switches, sensors, actuators and other items without removing any parts. Reading the Data List as the first step in troubleshooting is one method to save diagnostic time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch on (IG).


e.

Turn on the tester.


f.

Enter the following items: "Powertrain / ECT / Data List".


g.

According to the display on the tester, read "Data List".

Tester Display Measurement Item/Range Normal Condition
SPD (NT) Input Turbine Speed / Display: 50 r/min
HINT:
·

Lock-up ON (after warming up the engine); input turbine speed (NT) is equal to the engine speed.

·

Lock-up OFF (idling at N position); input turbine speed (NT) is nearly equal to the engine speed.




HINT:
·

SPD (NT) is always 0 while driving: Open or short in the sensor or circuit.

·

SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.





PROCEDURE

1.INSPECT SPEED SENSOR (SENSOR INSTALLATION)
a.
C133219

Make sure that the connector is properly connected, and check the speed sensor installation.

OK:

The installation bolt is tightened properly and there is no clearance between the sensor and transaxle case.




OK

2.CHECK TRANSMISSION WIRE

NG

REPAIR OR REPLACE SPEED SENSOR

2.CHECK TRANSMISSION WIRE
a.
C133270E07
1.938,1.198 1.563,2.156 true 2.104,1.188 2.771,2.135 true 1.427,3.802 1.104,4.24 true 1.75,3.802 2.042,4.24 true 1.125,0.302 2.458,0.458 1.333,0.156 10 false TCM Side Connector 1.094,2.646 2.583,2.802 1.49,0.156 10 false Sensor Side Connector 1.396,2.188 1.729,2.344 0.333,0.156 10 false NTO 2.677,2.177 3.021,2.333 0.344,0.156 10 false NTB 1.958,4.26 2.292,4.417 0.333,0.156 10 false NTO 0.885,4.26 1.167,4.448 0.281,0.188 10 false NTB

Remove the TCM.


b.

Disconnect the speed sensor connector from the transmission wire.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
NTO - NTO Below 1 Ω
NTB - NTB Below 1 Ω
NTO - NTB 10 kΩ or higher




OK

3.REPLACE SPEED SENSOR

NG

REPLACE TRANSMISSION WIRE

3.REPLACE SPEED SENSOR

NEXT

4.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0715 AND/OR P0717 OUTPUT AGAIN)
4.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0715 AND/OR P0717 OUTPUT AGAIN)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the intelligent tester main switch ON.



d.

When using the intelligent tester:

Select the following items: "Powertrain / ECT / DTC / Current or Pending".


e.

Read the DTCs using the intelligent tester.

Result:
Display (DTC output) Proceed to
Only "P0715 or P0717" is output A
No output B




A

REPLACE TCM

B

END