Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the TCM.

DTC No. DTC Detection Condition Trouble Area
P0705 (a) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic)
·

NSW input signal

·

R input signal

·

D input signal


(b) All switches are OFF simultaneously for NSW, R and D.
·

Short in park/neutral position switch circuit

·

Park/neutral position switch

·

TCM



WIRING DIAGRAM

C122821E08
5.667,0.75 5.99,0.927 0.323,0.177 10 false TCM 0.51,1.531 1.292,1.885 0.781,0.354 10 false From LH-IG Relay 1 2.729,3.01 3.521,3.188 0.792,0.177 10 false To ST Relay 3.177,0.417 3.531,0.594 0.354,0.177 10 false D4 3.177,0.604 4.177,0.979 1,0.375 10 false Park/Neutral Position Switch 4.896,3.802 5.167,3.979 0.271,0.177 10 false D5 4.896,1.823 5.167,2 0.271,0.177 10 false D5 4.896,1.417 5.167,1.594 0.271,0.177 10 false D5 4.896,1.229 5.063,1.406 0.167,0.177 10 false 16 4.896,1.635 5.063,1.813 0.167,0.177 10 false 15 4.885,3.604 5.052,3.781 0.167,0.177 10 false 11 5.219,1.417 5.375,1.594 0.156,0.177 10 false D 5.219,1.823 5.375,2 0.156,0.177 10 false R 5.208,3.792 5.552,3.969 0.344,0.177 10 false NSW 1.688,1.854 2.76,2.031 1.073,0.177 10 false GAUGE No. 2 3.615,1.281 3.813,1.458 0.198,0.177 10 false DL 3.573,1.823 3.771,2 0.198,0.177 10 false RL 3.313,1.458 3.521,1.635 0.208,0.177 10 false RB 3.823,2.323 3.979,2.5 0.156,0.177 10 false L 3.323,2.323 3.479,2.5 0.156,0.177 10 false B 3.115,1.5 3.271,1.677 0.156,0.177 10 false 1 3.135,2.323 3.292,2.5 0.156,0.177 10 false 4 4.01,1.302 4.167,1.479 0.156,0.177 10 false 7 4.01,1.708 4.167,1.885 0.156,0.177 10 false 2 4.01,2.323 4.167,2.5 0.156,0.177 10 false 9 0.531,2.344 1.198,2.729 0.667,0.385 10 false From Main Body ECU 2.708,3.198 5.083,3.375 2.375,0.177 10 false (in Engine Room Relay Block No. 1)

CAUTION / NOTICE / HINT

HINT:

According to the DATA LIST displayed on the intelligent tester, you can read the value of switches, sensors, actuators and other items without removing any parts. Reading the DATA LIST as the first step in troubleshooting is one method to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


READ DATA LIST


a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch on (IG).


d.

Turn on the tester.


e.

Select the following items: "Powertrain / ECT / Data List".


f.

According to the display on the tester, read "DATA LIST".

Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP SW Status / ON or OFF Shift lever position is;
P and N: ON
Except P or N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Shift SW status (R Range) PNP SW Status / ON or OFF Shift lever position is;
R: ON
Except R: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Shift SW status (D Range) PNP SW Status / ON or OFF Shift lever position is;
D and S: ON
Except D or S: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (D, R POSITION CIRCUIT)
a.
U188957E02
1.625,1.74 1.365,2.365 true 0.51,1.698 0.823,1.885 0.313,0.188 10 false D4 0.094,0.083 1.396,0.406 1.302,0.323 10 false Wire Harness Side: 0.802,0.74 2.656,0.969 1.854,0.229 10 false Park/Neutral Position Switch 1.26,2.385 1.469,2.563 0.208,0.177 10 false RB

Disconnect the park/neutral position switch connector.


b.

Turn the ignition switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Specified Condition
RB (D4-1) - Body ground 10 to 14 V




OK

2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)
a.

Remove the ST relay from the engine room relay block No. 1.

C366265E01
0.583,0.917 0.917,1.167 0.333,0.25 1.969,1.563 2.604,1.75 true 0.104,0.104 1.479,0.385 1.375,0.281 10 false Wire Harness Side: 0.646,0.948 1.135,1.208 0.49,0.26 10 false D4 2.656,1.677 3.146,1.938 0.49,0.26 10 false L 0.792,1.927 2.552,2.385 1.76,0.458 10 false Park/Neutral Position Switch (Front View) 3.719,0.135 4.958,0.531 1.24,0.396 10 false Engine Room Relay Block No. 1 3.938,0.99 4.688,1.26 0.75,0.271 10 false ST Relay


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
L (D4-9) - ST relay terminal 1 Below 1 Ω




OK

3.INSPECT ST RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ST RELAY
a.
B016200

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
3 - 5 10 kΩ or higher
3 - 5 Below 1 Ω
Apply battery voltage between terminals 1 and 2




OK

4.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPLACE ST RELAY

4.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.
C366266E01
0.167,0.104 1.552,0.333 1.385,0.229 10 false Wire Harness Side: 0.125,0.635 1.375,1.073 1.25,0.438 10 false Engine Room Relay Block No. 1 0.417,2.99 1.125,3.208 0.708,0.219 10 false ST Relay

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
ST relay terminal 2 - Body ground Below 1 Ω




OK

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C367266E02
0.25,1.667 0.583,1.917 0.333,0.25 1.167,1.594 0.958,1.188 0.958,1.188 0.76,1.188 false 1.583,1.594 2.031,0.917 2.031,0.917 2.198,0.917 false 1.927,1.604 2.177,1.188 2.177,1.188 2.344,1.188 false 0.844,2.667 1.031,2.667 1.031,2.667 1.24,2.021 false 2.479,2.49 2.219,2.49 2.219,2.49 1.75,2.031 false 0.146,0.073 1.656,0.333 1.51,0.26 10 false Component Side: 0.854,0.469 2.771,0.75 1.917,0.281 10 false Park/Neutral Position Switch 0.313,1.708 0.896,1.99 0.583,0.281 10 false D4 0.583,1.104 1.167,1.385 0.583,0.281 10 false B 2.26,0.844 2.844,1.125 0.583,0.281 10 false RL 2.396,1.104 2.979,1.385 0.583,0.281 10 false RB 2.594,2.406 3.177,2.688 0.583,0.281 10 false DL 0.667,2.583 1.25,2.865 0.583,0.281 10 false L

Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard resistance:
Tester Connection Shift Position Specified Condition
B (D4-4) - L (D4-9) P Below 1 Ω
Except P 10 kΩ or higher
RB (D4-1) - RL (D4-2) R Below 1 Ω
Except R 10 kΩ or higher
B (D4-4) - L (D4-9) N Below 1 Ω
Except N 10 kΩ or higher
RB (D4-1) - DL (D4-7) D, S, ''+'' and ''-'' Below 1 Ω
Except D, S, ''+'' and ''-'' 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (IG1 RELAY - TCM)

NG

6.CHECK HARNESS AND CONNECTOR (IG1 RELAY - TCM)
a.
U189035E02
2.115,1.406 1.896,1.927 true 2.26,1.406 2.417,1.927 true 0.031,0.031 1.26,0.25 1.229,0.219 10 false Wire Harness Side: 0.823,0.333 2.625,0.521 1.802,0.188 10 false TCM Connector (Front View) 0.188,0.792 0.458,0.938 0.271,0.146 10 false D5 1.833,1.948 1.969,2.094 0.135,0.146 10 false R 2.406,1.948 2.542,2.094 0.135,0.146 10 false D

Connect the park/neutral position switch connector.


b.

Disconnect the TCM connector.


c.

Turn the ignition switch on (IG), and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

Standard voltage:
Tester Connection Shift Position Specified Condition
R (D5-15) - Body ground R 10 to 14 V *
Except R Below 1 V
D (D5-16) - Body ground D 10 to 14 V
Except D Below 1 V


HINT:

*: The voltage will drop slightly due to lighting up of the back-up light.




OK

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.
U188964E02
1.688,3.813 1.604,4.333 true 2.271,1.667 2.729,2.052 true 0.083,0.063 1.365,0.25 1.281,0.188 10 false Wire Harness Side: 0.792,0.594 2.74,0.823 1.948,0.229 10 false Park/Neutral Position Switch 0.438,1.073 0.708,1.281 0.271,0.208 10 false D4 0.458,2.823 0.781,3.031 0.323,0.208 10 false D5 1.281,2.646 2.396,2.927 1.115,0.281 10 false TCM Connector 1.438,4.354 1.781,4.531 0.344,0.177 10 false NSW 2.771,2.01 2.979,2.188 0.208,0.177 10 false B

Disconnect the TCM connector.


b.

Turn the ignition switch off.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):
Tester Connection Specified Condition
B (D4-4) - NSW (D5-11) Below 1 Ω


Standard resistance (Check for short):
Tester Connection Specified Condition
B (D4-4) or NSW (D5-11) - Body ground 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR