Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2013.04–2016.05
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in lock-up condition when brakes are suddenly applied.

When the brake pedal is depressed, this switch sends a signal to the TCM. Then the TCM cancels the operation of the lock-up clutch while braking is in progress.

DTC No. DTC Detection Condition Trouble Area
P0724 The stop light switch remains ON even when the vehicle is driven in a STOP (less than 3 km/h (2 mph)) and GO (30 km/h (19 mph) or more) fashion 5 times (2-trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch

·

TCM



MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains ON. When the stop light switch remains ON during "stop and go" driving, the TCM interprets this as a fault in the stop light switch, illuminates the MIL, and stores the DTC. The vehicle must stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) 5 times for 2 consecutive driving cycles in order to set this DTC.

WIRING DIAGRAM

C142135E05
6.177,2.167 6.729,2.385 0.552,0.219 10 false TCM 5.938,1.021 6.302,1.24 0.365,0.219 10 false STP 5.615,0.781 5.938,1 0.323,0.219 10 false 12 5.271,1.135 5.51,1.354 0.24,0.219 10 false 1 4.594,1.135 4.833,1.354 0.24,0.219 10 false 2 3.771,1.167 4.198,1.385 0.427,0.219 10 false STOP 2.052,1.188 2.479,1.406 0.427,0.219 10 false ALT 1.083,1.188 1.792,1.406 0.708,0.219 10 false FL MAIN 2.677,1.177 3.688,1.635 1.01,0.458 10 false RH-MAIN-JB 0.875,1.698 1.771,1.917 0.896,0.219 10 false Battery 4.448,1.531 5.896,2.052 1.448,0.521 10 false Stop Light Switch 5.625,1.01 5.927,1.229 0.302,0.219 10 false D5 4.448,1.354 4.885,1.573 0.438,0.219 10 false A33

PROCEDURE

1.READ VALUE USING DATA LIST (STP SIGNAL)
HINT:

According to the Data List displayed on the intelligent tester, you can read the value of switches, sensors, actuators and other items without removing any parts. Reading the Data List as the first step in troubleshooting is one method to save diagnostic time.


a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch on (IG).


d.

Turn on the tester.


e.

Enter the following items: "Powertrain / ECT / Data List".


f.

According to the display on the tester, read "Data List".

Standard:
Tester Display Measurement Item/Range Normal Condition
Stop Light Switch Stop light switch status/
ON or OFF
·

Brake pedal is depressed: ON

·

Brake pedal is released: OFF




NOTICE:

In the table above, the conditions listed under "Normal Condition" are reference conditions. Do not depend solely on these reference conditions when deciding whether a part is faulty.




NG

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Interior>LIGHTING>STOP LIGHT SWITCH>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)
a.
U189036E01
0.102,0.006 1.407,0.145 1.305,0.139 10 Wire Harness Side: 0.639,0.303 2.442,0.448 1.803,0.145 10 TCM Connector (Front View) 0.192,0.772 0.464,0.938 0.272,0.166 10 D5 1.437,1.965 1.729,2.114 0.292,0.149 10 STP 1.787,1.41 1.624,1.973 false

Install the stop light switch assembly.


b.

Disconnect the TCM connector.


c.

Measure the voltage according to the value(s) in the table below when the brake pedal is depressed and released.

Standard voltage:
Tester Connection Condition Specified Condition
D5-12 (STP) - Body ground Brake pedal is depressed 10 to 14 V
D5-12 (STP) - Body ground Brake pedal is released Below 1 V




OK

REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR