Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P2757  Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU)  


SYSTEM DESCRIPTION

The TCM uses the signals from the throttle position sensor, air-flow meter, turbine (input) speed sensor, output speed sensor and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.

C133226E04
1.292,1.542 0.875,1.927 0.875,1.927 0.74,1.927 true 2.271,0.479 2.188,0.479 2.188,0.479 1.948,1.302 true 2.74,1.563 3.135,2.031 3.135,2.031 3.135,2.146 true 0.302,1.833 0.792,2 0.49,0.167 10 false Sleeve 2.313,0.406 3.167,0.594 0.854,0.188 10 false Spool Valve 2.781,2.156 3.667,2.344 0.885,0.188 10 false Solenoid Coil 5.323,2.146 5.896,2.323 0.573,0.177 10 false Current 3.76,0.375 4.406,0.708 0.646,0.333 10 false Hydraulic Pressure

The TCM compares the engagement condition of the lock-up clutch with the lock-up schedule in the TCM memory to detect shift solenoid valve SLU, valve body and torque converter assembly mechanical problems.

DTC No. DTC Detection Condition Trouble Area
P2757 When both of the following are detected (2-trip detection logic):
·

Lock-up does not occur when requested.

·

Transmission fluid pressure switch No. 3 is OFF.


When both of the following are detected (2-trip detection logic):
·

Transmission fluid pressure switch No. 3 is ON when lock-up does not occur.

·

Lock-up occurs when the shift solenoid valve SLU is requested to turn on in the lock-up range.


·

Shift solenoid valve SLU remains open or closed

·

Valve body is blocked

·

Torque converter assembly

·

Automatic transaxle (clutch, brake or gear, etc.)

·

Line pressure is too low



MONITOR DESCRIPTION

Torque converter lock-up is controlled by the TCM based on the turbine (input) speed sensor NT, output speed sensor NC, engine rpm, engine load, engine temperature, vehicle speed, transmission fluid temperature, and gear selection. The TCM determines the lock-up status of the torque converter by comparing the engine rpm (NE) to the input turbine rpm (NT). The TCM calculates the actual transmission gear by comparing input turbine rpm (NT) to output shaft rpm (NC). When conditions are appropriate, the TCM requests "lock-up" by applying control voltage to the shift solenoid SLU. When the SLU is turned on, it applies pressure to the lock-up relay valve and locks the torque converter assembly.

If the TCM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the TCM interprets this as a fault in the shift solenoid valve SLU or lock-up system performance.

The TCM will turn on the MIL and store the DTC.

Example:

When any of the following is met, the system judges it as a malfunction.

·

There is a difference in rotation between the input side (engine speed) and output side (input turbine speed) of the torque converter when the TCM commands lock-up.

(Engine speed is at least 70 rpm greater than input turbine speed.)

·

There is no difference in rotation between the input side (engine speed) and output side (input turbine speed) of the torque converter when the TCM commands lock-up off.

(The difference between engine speed and input turbine speed is less than 20 rpm.)


CAUTION / NOTICE / HINT

ACTIVE TEST


HINT:

Performing the Active Test using the intelligent tester allows relays, VSVs, actuators and other items to be operated without removing any parts. Performing the Active Test as the first step in troubleshooting is one method to save diagnostic time.

It is possible to display the Data List during the Active Test.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch on (IG).


e.

Turn on the tester.


f.

Enter the following items: "Powertrain / ECT / Active Test".


g.

According to the display on the tester, perform "Active Test".

Tester Display Test Part Control Range Diagnostic Note
Activate the Lock Up [Test Details]
Control the shift solenoid SLU to set the automatic transaxle to the lock-up condition.
[Vehicle Condition]
·

Throttle valve opening angle: Less than 35%

·

Vehicle speed: 60 km/h (37 mph) or more


[Lock-up]
0: OFF / 1: ON
Possible to check the SL operation.

HINT:
·

This test can be conducted when the vehicle speed is 60 km/h (37 mph) or more.

·

This test can be conducted with the 6th gear.




h.

Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

U190026E02
2.667,1.563 2.396,1.698 2.396,1.698 2.094,1.698 false 4.469,1.979 4.833,1.719 4.833,1.719 5.25,1.719 false 4.813,2.146 5.115,2.313 5.115,2.313 5.542,2.313 false 1.885,0.76 3.354,1.177 1.469,0.417 10 false Accelerator Pedal Opening Angle 0.969,1.615 2.115,2.26 1.146,0.646 10 false Accelerator Pedal Fully Released 2.135,2.156 3.281,2.573 1.146,0.417 10 false Engine Speed 4.563,2.438 4.958,2.781 0.396,0.344 10 false Time 5.302,1.635 6.365,2.031 1.063,0.396 10 false Lock-up OFF 5.594,2.229 6.615,2.615 1.021,0.385 10 false Lock-up ON

HINT:
·

When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is on.

·

Slowly release, but not fully, the accelerator pedal in order to decelerate. (Fully releasing the pedal will close the throttle valve and lock-up may be turned off automatically.)





PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2757)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the intelligent tester on.


c.

Enter the following items: "Powertrain / ECT / DTC / Current or Pending".


d.

Read the DTCs using the intelligent tester.

Result:
Display (DTC output) Proceed to
Only "P2757" is output A
"P2757" and other DTCs are output B


HINT:

If any other codes besides "P2757" are output, perform troubleshooting for those DTCs first.




A

2.INSPECT SHIFT SOLENOID VALVE SLU

B

GO TO DTC CHART

2.INSPECT SHIFT SOLENOID VALVE SLU
a.
G102540E04
1.76,3.115 2.469,2.76 false 1.49,3.115 0.781,2.802 false 0.771,1.24 1.479,0.885 false 2.49,1.219 1.781,0.906 false 0.115,0.063 1.938,0.385 1.823,0.323 10 false Shift Solenoid Valve SLU: 0.646,1.177 0.958,1.375 0.313,0.198 10 false 1 2.552,1.167 2.865,1.365 0.313,0.198 10 false 2 1.198,4.167 1.51,4.365 0.313,0.198 10 false (-) 1.917,4.177 2.229,4.375 0.313,0.198 10 false (+) 0.635,2.698 0.948,2.896 0.313,0.198 10 false 1 2.531,2.656 2.844,2.854 0.313,0.198 10 false 2

Remove the shift solenoid valve SLU.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
1 - 2 5.0 to 5.6 Ω
(at 20°C (68°F))



c.

Connect a positive (+) lead through a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

OK:

The solenoid makes an operating sound.




OK

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

REPLACE SHIFT SOLENOID VALVE SLU

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK:

There are no foreign objects on each valve.



OK

4.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPLACE TRANSMISSION VALVE BODY ASSEMBLY

4.INSPECT TORQUE CONVERTER ASSEMBLY

OK:

The torque converter assembly operates normally.



OK

REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

REPLACE TORQUE CONVERTER ASSEMBLY