Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0778  Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2)  


DESCRIPTION

Shifting from 1st to 6th is performed in combination with "ON" and "OFF" operation of the shift solenoid valves SL1, SL2, SL3, SL4 and SL which is controlled by the TCM. If an open or short circuit occurs in any of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART).

DTC No. DTC Detection Condition Trouble Area
P0778 The TCM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears. (1-trip detection logic)
·

Output signal duty equals to 100%.

(NOTE: SL2 output signal duty is less than 100% under normal condition.)


·

Open or short in shift solenoid valve SL2 circuit

·

Shift solenoid valve SL2

·

TCM



MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL2 circuit. The TCM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any of the shift solenoid valve circuits, the TCM detects the problem, illuminates the MIL and stores the DTC. The TCM also performs the fail-safe function and turns the other normal shift solenoid valves on or off. (In case of an open or short circuit, the TCM stops sending current to the circuit.)

While driving and shifting gears, if the TCM detects an open or short in the shift solenoid valve SL2 circuit, the TCM determines there is a malfunction (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART).

WIRING DIAGRAM

C133261E74
5.646,0.521 6.01,0.854 0.365,0.333 10 false TCM 2.135,3.854 3.51,4.281 1.375,0.427 10 false Transaxle Assembly 5.083,1.802 5.625,1.969 0.542,0.167 10 false SL2+ 5.823,1.083 6.365,1.25 0.542,0.167 10 false +B 5.063,3.188 5.604,3.354 0.542,0.167 10 false SL2- 1.594,2.354 3.646,2.74 2.052,0.385 10 false Shift Solenoid Valve SL2 4.875,1.563 5.031,1.74 0.156,0.177 10 false 9 4.865,2.948 5.021,3.125 0.156,0.177 10 false 8 1.417,2 1.573,2.177 0.156,0.177 10 false 2 1.406,2.677 1.563,2.854 0.156,0.177 10 false 1

CAUTION / NOTICE / HINT

HINT:

The shift solenoid valve SL2 is turned on or off automatically when the shift lever is in the D position:

TCM command gearshift 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve SL2 OFF OFF OFF ON ON ON


PROCEDURE

1.INSPECT TRANSMISSION WIRE (SL2)
a.
C133212E92
1.5,0.729 1.031,0.375 true 1.677,0.74 2.323,0.427 true 0.677,0.281 1.031,0.427 0.354,0.146 10 false SL2+ 2.365,0.323 2.698,0.469 0.333,0.146 10 false SL2-

Remove the TCM from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
9 (SL2+) - 8 (SL2-) 5.0 to 5.6 Ω
(at 20°C (68°F))



c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Check for short:
Tester Connection Specified Condition
9 (SL2+) - Body ground 10 kΩ or higher
8 (SL2-) - Body ground 10 kΩ or higher




NG

2.INSPECT SHIFT SOLENOID SL2

OK

REPLACE TCM

2.INSPECT SHIFT SOLENOID SL2
a.
G102540E02
1.76,3.115 2.469,2.76 false 1.49,3.115 0.781,2.802 false 1.76,0.906 2.469,0.552 false 1.479,0.896 0.771,0.583 false 0.115,0.063 1.938,0.385 1.823,0.323 10 false Shift Solenoid Valve SL2: 0.625,0.479 0.938,0.677 0.313,0.198 10 false 1 2.542,0.458 2.854,0.656 0.313,0.198 10 false 2 1.198,4.167 1.51,4.365 0.313,0.198 10 false (-) 1.917,4.177 2.229,4.375 0.313,0.198 10 false (+) 0.635,2.698 0.948,2.896 0.313,0.198 10 false 1 2.531,2.656 2.844,2.854 0.313,0.198 10 false 2

Remove the shift solenoid valve SL2.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
1 - 2 5.0 to 5.6 Ω
(at 20°C (68°F))



c.

Connect a positive (+) lead through a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

OK:

The solenoid makes an operating sound.




OK

REPLACE TRANSMISSION WIRE

NG

REPLACE SHIFT SOLENOID SL2