The TCM uses signals from the throttle position sensor, air-flow meter, turbine (input) speed sensor, intermediate (counter) speed sensor and crankshaft position sensor to help determine the engagement timing of the lock-up clutch. The TCM monitors the engagement of the clutch using the turbine (input) speed sensor, intermediate (counter) speed sensor and crankshaft position sensor.
Then the TCM compares the engagement condition of the lock-up clutch with the lock-up schedule in the TCM memory to detect shift solenoid valve SL, valve body and torque converter assembly mechanical problems.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0741 | When both of the following are detected (2-trip detection logic):
·
Lock-up does not occur when requested. ·
Transmission fluid pressure switch No. 3 is ON. |
·
Shift solenoid valve SL remains closed ·
Valve body is blocked ·
Torque converter assembly ·
Automatic transaxle (clutch, brake or gear etc.) ·
Line pressure is too low |
Torque converter lock-up is controlled by the TCM based on the speed sensor (NT), speed sensor (NC), engine rpm, engine load, engine temperature, vehicle speed, transmission fluid temperature, and gear selection. The TCM determines the lock-up status of the torque converter by comparing the engine rpm (NE) to the input turbine rpm (NT). The TCM calculates the actual transmission gear by comparing the input turbine rpm (NT) to the counter gear rpm (NC). When conditions are appropriate, the TCM requests "lock-up" by applying control voltage to the shift solenoid SL. When the SL is turned on, it applies pressure to the lock-up relay valve and locks the torque converter assembly.
If the TCM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the TCM interprets this as a fault in the shift solenoid valve SL or lock-up system performance. The TCM will turn on the MIL and store the DTC.
Example:
When any of the following is met, the system judges it as a malfunction.
There is a difference in rotation between the input side (engine speed) and output side (input turbine speed) of the torque converter when the TCM commands lock-up.
(Engine speed is at least 70 rpm greater than the input turbine speed.)
There is no difference in rotation between the input side (engine speed) and output side (input turbine speed) of the torque converter when the TCM commands lock-up off.
(The difference between the engine speed and input turbine speed is less than 20 rpm.)
Performing the Active Test using the intelligent tester allows relays, VSVs, actuators and so on to operate without removing any parts. Performing the Active Test as the first step in troubleshooting is one method to save diagnostic time.
It is possible to display the Data List during the Active Test.
PERFORM ACTIVE TEST
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
When using the intelligent tester:
Enter the following items: "Powertrain / ECT / Active Test".
According to the display on the tester, perform "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Active the Lock Up | [Test Details]
Control the shift solenoid SL to set the automatic transaxle to the lock-up condition. [Vehicle Condition] Vehicle Speed: 60 km/h (37 mph) or more. |
[Lock-up]
0: OFF / 1: ON |
Possible to check the SL operation. |
This test can be conducted when the vehicle speed is 60 km/h (37 mph) or more.
This test can be conducted in the 6th gear.
Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.
When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is on.
Slowly release, but not fully, the accelerator pedal in order to decelerate. (Fully releasing the pedal will close the throttle valve and lock-up may be turned off.)
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester on.
Enter the following items: "Powertrain / ECT / DTC / Current or Pending".
Read the DTCs using the intelligent tester.
| Display (DTC output) | Proceed to |
|---|---|
| Only "P0741" is output | A |
| "P0741" and other DTCs are output | B |
If any other codes besides "P0741" are output, perform the troubleshooting for those DTCs first.
A
B
Remove the TCM from the transaxle.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
|---|---|
| 6 (SL) - Body ground | 11 to 15 Ω
(at 20°C (68°F)) |
NG
OK
Remove the shift solenoid valve SL.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
|---|---|
| Solenoid Connector (SL) - Solenoid Body (SL) | 11 to 15 Ω
(at 20°C (68°F)) |
OK
NG
Remove the shift solenoid valve SL.
Connect a positive (+) lead to the terminal of the solenoid connector, and a negative (-) lead to the solenoid body.
The solenoid valve makes an operating sound.
OK
NG
Check the valve body assembly (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL).
There are no foreign objects on each valve and the valves operate smoothly.
OK
NG
Check the torque converter assembly (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).
The torque converter assembly operates normally.
OK
NG