Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2013.04–2016.05
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  U0100  Lost Communication with ECM / PCM "A"  


DESCRIPTION

The engine control unit intercommunicates with the TCM using the Controller Area Network (CAN).

If there is a problem in this intercommunication, the TCM sets a DTC.

DTC No. DTC Detection Condition Trouble Area
U0100

Following conditions are met for 1.25 seconds (1-trip detection logic):

(a)

Ignition switch on (IG)

(b)

Battery voltage is 10.5 V or more

(c)

No intercommunication between the ECM and TCM



·

Wire harness

·

ECM

·

TCM



WIRING DIAGRAM

C157362E02
5.615,0.281 6.052,0.469 0.438,0.188 10 false ECM 0.146,0.781 1.125,1.146 0.979,0.365 10 false From RH-IG Relay 1 1.354,1.073 2.438,1.26 1.083,0.188 10 false RH ECU-IG 2.24,0.24 3.156,0.427 0.917,0.188 10 false G9 2.25,0.396 4.104,0.583 1.854,0.188 10 false Transmission Control Switch 2.438,2.323 2.854,2.51 0.417,0.188 10 false TCM 2.74,2.917 3.146,3.104 0.406,0.188 10 false CAN- 5.177,2.917 5.583,3.104 0.406,0.188 10 false CAN- 2.729,3.323 3.208,3.51 0.479,0.188 10 false CAN+ 5.167,3.313 5.646,3.5 0.479,0.188 10 false CAN+ 2.104,3.167 2.354,3.354 0.25,0.188 10 false +B 2.135,3.552 2.385,3.74 0.25,0.188 10 false E1 3.24,2.927 3.531,3.115 0.292,0.188 10 false D5 3.24,3.313 3.531,3.5 0.292,0.188 10 false D5 1.813,3.177 2.104,3.365 0.292,0.188 10 false D5 1.813,3.563 2.104,3.75 0.292,0.188 10 false D5 1.813,2.969 2,3.115 0.188,0.146 10 false 18 1.854,3.375 2.042,3.521 0.188,0.146 10 false 8 3.292,2.719 3.479,2.865 0.188,0.146 10 false 7 3.281,3.125 3.469,3.271 0.188,0.146 10 false 6 4.865,0.833 5.156,1.021 0.292,0.188 10 false A7 4.865,0.656 5.052,0.802 0.188,0.146 10 false 25 4.865,1.24 5.156,1.427 0.292,0.188 10 false A7 4.865,1.052 5.052,1.198 0.188,0.146 10 false 51 4.865,1.646 5.156,1.833 0.292,0.188 10 false A7 4.854,1.458 5.042,1.604 0.188,0.146 10 false 16 4.865,2.917 5.156,3.104 0.292,0.188 10 false D1 4.885,2.729 5.073,2.875 0.188,0.146 10 false 1 4.865,3.313 5.156,3.5 0.292,0.188 10 false D1 4.906,3.135 5.094,3.281 0.188,0.146 10 false 2 5.177,0.823 5.583,1.01 0.406,0.188 10 false S 5.167,1.24 5.646,1.427 0.479,0.188 10 false SFTD 5.167,1.656 5.646,1.844 0.479,0.188 10 false SFTU 0.104,3.104 1.083,3.708 0.979,0.604 10 false From C/OPN Relay 3.219,0.708 3.448,0.854 0.229,0.146 10 false 13 3.25,1.125 3.479,1.271 0.229,0.146 10 false 4 2.198,1.531 2.427,1.677 0.229,0.146 10 false 11 2.26,0.719 2.49,0.865 0.229,0.146 10 false 6 3.24,1.542 3.469,1.688 0.229,0.146 10 false 5

CAUTION / NOTICE / HINT

HINT:
·

Refer to inspection procedures for the CAN communication system (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>SYSTEM DESCRIPTION).

·

If the CAN communication malfunctions, the TCM cannot receive the current data from the ECM. In this case, the freeze frame data output from the TCM have not been updated, so the data will not be useful for the inspection. However, reading the Data List as the first step in troubleshooting is effective to find malfunctions.



PROCEDURE

1.CHECK ECU TERMINAL VOLTAGE (+B AND E1 TERMINALS)
a.
U189037E01
0.102,0.003 1.407,0.175 1.305,0.172 10 Wire Harness Side: 0.639,0.299 2.442,0.445 1.803,0.145 10 TCM Connector (Front View) 0.19,0.772 0.462,0.918 0.272,0.145 10 D5 0.674,1.99 0.877,2.139 0.203,0.149 10 E1 1.648,1.991 1.868,2.139 0.220,0.149 10 +B 1.05,1.332 0.854,1.979 false 1.223,1.525 1.723,1.986 false

Disconnect the TCM connector.


b.

Turn the ignition switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Specified Condition
D5-18 (+B) - Body ground 9 to 14 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
D5-8 (E1) - Body ground Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (TCM - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (TCM - ECM)
a.
U189045E02
0.5,1.25 0.198,2.198 true 0.583,1.26 1.01,2.208 true 2.073,3.615 1.5,4.302 true 2.219,3.604 2.458,4.292 true 0.167,0.073 1.583,0.229 1.417,0.156 10 false Wire Harness Side: 0.927,0.448 2.833,0.646 1.906,0.198 10 false ECM Connector (Front View) 0.865,2.51 2.74,2.698 1.875,0.188 10 false TCM Connector (Front View) 1.344,4.344 1.823,4.51 0.479,0.167 10 false CAN+ 2.365,4.333 2.729,4.49 0.365,0.156 10 false CAN- 0.885,2.25 1.385,2.427 0.5,0.177 10 false CAN+ 0.073,2.229 0.438,2.385 0.365,0.156 10 false CAN- 0.24,0.479 0.531,0.688 0.292,0.208 10 false D1 0.24,2.656 0.531,2.865 0.292,0.208 10 false D5

Disconnect the TCM connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
D5-6 (CAN+) - D1-2 (CAN+) Below 1 Ω
D5-7 (CAN-) - D1-1 (CAN-) Below 1 Ω
D5-6 (CAN+) or D1-2 (CAN+) - Body ground 1 MΩ or more
D5-7 (CAN-) or D1-1 (CAN-) - Body ground 1 MΩ or more




OK

3.CHECK IF DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK IF DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTC.


c.

Replace the TCM.

HINT:

Replace the TCM with the TCM of a normally functioning vehicle of the same model.



d.

Start the engine.


e.

Read the DTCs.

Result:
Display (DTC Output) Proceed to
P0100 A
No DTC B




A

REPLACE ECM

B

REPLACE TCM