Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › VALVE BODY ASSEMBLY
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292116 VALVE BODY ASSEMBLY A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  VALVE BODY ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 35418 1.INSTALL MANUAL VALVE

a.
C138517

Coat the manual valve with ATF and install it to the valve body.


Hide 35410 2.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.

Coat the O-ring of the transmission wire with ATF.


b.
C136689E11
2.75,1.563 3.031,2.74 3.031,2.74 2.292,2.177 false 2.031,2.146 1.479,2.854 1.479,2.854 0.865,2.344 false 1.615,2.156 1.479,2.854 1.479,2.854 1.208,2.177 false 2.073,0.969 2.542,0.188 2.542,0.188 2.771,0.188 false 1.333,0.958 1.698,0.229 1.698,0.229 1.76,0.229 false 0.896,0.917 1.167,0.24 1.167,0.24 1.229,0.24 false 0.51,1.375 0.25,1 false 0.479,2.021 0.271,2.365 false 0.073,1.927 0.24,2.094 0.167,0.167 10 false *1 3.031,1.479 3.208,1.646 0.177,0.167 10 true *1 2.813,0.115 2.958,0.271 0.146,0.156 10 false A 1.458,2.885 1.604,3.042 0.146,0.156 10 false B 0.135,0.854 0.281,1.01 0.146,0.156 10 false D 1.26,0.156 1.406,0.313 0.146,0.156 10 false C 0.156,2.323 0.302,2.479 0.146,0.156 10 false E 3.031,2.781 3.177,2.938 0.146,0.156 10 false B 1.813,0.146 1.958,0.302 0.146,0.156 10 false B

Confirm that the manual valve lever is positioned as shown in the illustration and install the valve body assembly to the transaxle case with the 11 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)

Bolt length:
Bolt A:

25 mm (0.98 in.)

Bolt B:

30 mm (1.18 in.)

Bolt C:

35 mm (1.38 in.)

Bolt D:

45 mm (1.77 in.)

Bolt E:

55 mm (2.17 in.)


NOTICE:
·

When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case to interfere with each other.

·

Be sure to insert the pin of the manual valve lever into the groove on the end of the manual valve.

·

First, temporarily tighten the bolts marked by (*1) in the illustration because they are positioning bolts.




Hide 35330 3.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.
C136688E09
1.802,0.375 2.042,0.375 false 2.083,0.292 2.563,0.469 0.479,0.177 10 false O-Ring

Coat a new O-ring with ATF and install it to the oil strainer.

NOTICE:

Ensure that the O-ring is not twisted or pinched.



b.
C136687

Install the oil strainer to the valve body with the 2 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 35106D 4.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C134963

Install the 2 transmission oil cleaner magnets to the automatic transaxle oil pan sub-assembly.


b.

Install a new gasket to the automatic transaxle oil pan sub-assembly.


c.
C288671

Install the automatic transaxle oil pan sub-assembly to the transaxle case with the 17 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.

Clean and degrease the bolt and the installation hole in the transaxle case.


e.

Apply adhesive to the bolt.

adhesive:

Toyota Genuine Seal Packing 1344, Three Bond 1344 or equivalent



f.
C356364

Install the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

NOTICE:
·

In order to ensure proper sealing of the bolts, apply adhesive to the bolts and install them within 10 minutes of adhesive application.

·

Completely remove any oil or grease from the contact surfaces of the transaxle case and automatic transaxle oil pan sub-assembly with the gasket before installation.




Hide 30500 5.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY