Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY › 2013.04–2016.05
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292121 AUTOMATIC TRANSAXLE ASSEMBLY A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C154963

Engage the splines of the input shaft and turbine runner.


b.
C154964

Engage the splines of the stator shaft and the stator while turning the torque converter assembly.

HINT:

If the stator shaft splines are difficult to engage with the stator splines, move the torque converter assembly back approximately 10 mm and engage the splines while turning the torque converter assembly.



c.
C154965

Turn the torque converter assembly to engage the key of the oil pump drive gear into the slot on the torque converter assembly.


d.
C191042E12
0.979,2.469 0.979,3.063 false 1.385,0.969 1.229,0.313 1.229,0.313 1.104,0.313 true 2.573,0.792 2.438,0.917 2.438,0.917 2.438,1.031 false 2.698,1.49 2.573,1.625 2.573,1.625 2.573,1.729 false 2.156,0.323 2.271,0.469 0.115,0.146 10 false A 0.938,0.229 1.094,0.406 0.156,0.177 10 false *1 0.906,3.073 1.083,3.25 0.177,0.177 10 false *2 2.51,1.76 2.688,1.938 0.177,0.177 10 false *2 2.354,1.052 2.51,1.229 0.156,0.177 10 false *1

Using a vernier caliper and a straightedge, measure dimension "A" between the transaxle contact surfaces of the engine*1 and the torque converter assembly contact surfaces of the drive plate*2. (#)

NOTICE:

Make sure to deduct the thickness of the straightedge.



e.
C191041E03
2.378,0.341 2.499,0.497 0.121,0.156 10 B

Using a vernier caliper and a straightedge, measure dimension "B" shown in the illustration and check that "B" is greater than "A" which was measured in step (#).

Standard:

A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the transaxle is installed to the engine with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.




Hide 33403M 2.INSTALL SPEEDOMETER DRIVEN HOLE (ATM) COVER SUB-ASSEMBLY

a.

Apply Toyota genuine ATF WS to a new O-ring and install it to the speedometer driven hole (ATM) cover sub-assembly.


b.
C135002

Install the speedometer driven hole (ATM) cover sub-assembly to the automatic transaxle assembly with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 33823 3.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C139615

Install the No. 1 transmission control cable bracket to the automatic transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 89530C 4.INSTALL TCM

a.

Install the TCM to the automatic transaxle assembly.


b.
C139840E06
1.667,0.458 1.823,0.188 true 2.198,0.698 2.292,0.5 true 2.281,0.354 2.385,0.521 0.104,0.167 10 true 1 1.823,0.021 1.99,0.208 0.167,0.188 10 true 2

Tighten the 2 bolts in the order shown in the illustration.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


c.
C139242

Connect the connector to the TCM and lock the lock lever to secure the connector.


Hide 12325A 5.INSTALL ENGINE MOUNTING BRACKET LH

a.
C367640

Install the engine mounting bracket LH to the automatic transaxle assembly with the 4 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 6.INSTALL OIL COOLER HOSE

a.

w/o Air Cooled Oil Cooler

i.
C202159

Install the 2 oil cooler hoses to the automatic transaxle assembly with the 2 clips.



b.

w/ Air Cooled Oil Cooler

i.
C204422

Install the 2 oil cooler hoses to the automatic transaxle assembly with the 2 clips.



Hide 7.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C161404

Install the 2 wire harness clamp brackets to the automatic transaxle assembly with the 2 bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 8.INSTALL WIRE HARNESS

a.
C139612E02
1.365,0.74 1.521,0.917 0.156,0.177 10 true A 2.26,1.01 2.417,1.188 0.156,0.177 10 false B

Install the 2 wire harnesses to the automatic transaxle assembly with the 2 bolts.

Torque:
A : 19 N*m (194 kgf*cm, 14 ft.*lbf)
B : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 30500 9.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C206210E06
1.542,1.073 1.958,1.073 false 2,0.99 3.125,1.979 1.125,0.99 10 false Torque Converter Assembly Centerpiece 0.292,1.01 1.146,1.281 0.854,0.271 10 false Crankshaft

Apply clutch spline grease to the contact surface between the crankshaft and torque converter assembly centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum spread:

About 1 g (0.0353 oz.)



b.
C202448E01
1.221,2.333 1.342,2.489 0.122,0.155 10 A 1.647,2.28 1.768,2.435 0.122,0.155 10 A 2.542,2.36 2.664,2.516 0.122,0.155 10 A 2.729,2.979 2.851,3.134 0.122,0.155 10 A 2.792,3.543 2.913,3.698 0.122,0.155 10 A 2.738,3.863 2.859,4.018 0.122,0.155 10 A 0.875,2.728 0.996,2.883 0.122,0.155 10 B 0.924,4.048 1.046,4.203 0.122,0.155 10 C 1.124,4.192 1.245,4.347 0.122,0.155 10 D 1.427,4.351 1.548,4.506 0.122,0.155 10 D 2.393,4.218 2.514,4.373 0.122,0.155 10 D

Keeping the engine and automatic transaxle assembly in a horizontal position, align the knock pins with each hole on the automatic transaxle assembly and tighten the 11 bolts shown in the illustration.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

(Bolt A)

64 N*m (653 kgf*cm, 47 ft.*lbf)

(Bolt B)

46 N*m (469 kgf*cm, 34 ft.*lbf)

(Bolt C)

43 N*m (439 kgf*cm, 32 ft.*lbf)

(Bolt D)


NOTICE:
·

Confirm that the 2 knock pins are on the transaxle fitted surface of the engine cylinder block before the transaxle installation.

·

Do not forcibly pry on the automatic transaxle assembly.

·

Check that the torque converter assembly rotates.



HINT:

Bolt length:

·

55 mm (Bolt A)

·

50 mm (Bolt B)

·

41 mm (Bolt C)

·

33 mm (Bolt D)




c.

Clean the installation holes for the torque converter assembly set bolts.


d.
A057108E67
2.156,0.26 2.031,0.26 2.031,0.26 1.75,1.292 false 2.198,0.156 2.833,0.333 0.635,0.177 10 false Adhesive

Apply a few drops of adhesive 1324 to 2 ore 3 threads of the 6 set bolts tip.


e.
A205885

Tighten the 6 torque converter assembly set bolts.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

HINT:
·

First tighten the positioning bolt.

·

The positioning bolt is black.




f.
U189404

Install the transmission breather skirt to the engine cylinder head with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


g.

Install the breather plug hose to the transmission breather skirt with the clip.


Hide 11361J 10.INSTALL FLYWHEEL HOUSING UNDER COVER

a.
C139871

Install the flywheel housing under cover with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Install the engine assembly with transaxle (see page Engine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION).