32000
1.INSTALL TORQUE CONVERTER ASSEMBLY
Engage the splines of the input shaft and turbine runner.
Engage the splines of the stator shaft and the stator while turning the torque converter assembly.
If the stator shaft splines are difficult to engage with the stator splines, move the torque converter assembly back approximately 10 mm and engage the splines while turning the torque converter assembly.
Turn the torque converter assembly to engage the key of the oil pump drive gear into the slot on the torque converter assembly.
Using a vernier caliper and a straightedge, measure dimension "A" between the transaxle contact surfaces of the engine*1 and the torque converter assembly contact surfaces of the drive plate*2. (#)
Make sure to deduct the thickness of the straightedge.
Using a vernier caliper and a straightedge, measure dimension "B" shown in the illustration and check that "B" is greater than "A" which was measured in step (#).
A + 1 mm (0.0394 in.) or more
Make sure to deduct the thickness of the straightedge.
If the transaxle is installed to the engine with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.
33403M
2.INSTALL SPEEDOMETER DRIVEN HOLE (ATM) COVER SUB-ASSEMBLY
Apply Toyota genuine ATF WS to a new O-ring and install it to the speedometer driven hole (ATM) cover sub-assembly.
Install the speedometer driven hole (ATM) cover sub-assembly to the automatic transaxle assembly with the bolt.
33823
3.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Install the No. 1 transmission control cable bracket to the automatic transaxle assembly with the 2 bolts.
89530C
4.INSTALL TCM
Install the TCM to the automatic transaxle assembly.
Tighten the 2 bolts in the order shown in the illustration.
Connect the connector to the TCM and lock the lock lever to secure the connector.
12325A
5.INSTALL ENGINE MOUNTING BRACKET LH
Install the engine mounting bracket LH to the automatic transaxle assembly with the 4 bolts.
6.INSTALL OIL COOLER HOSE
w/o Air Cooled Oil Cooler
Install the 2 oil cooler hoses to the automatic transaxle assembly with the 2 clips.
w/ Air Cooled Oil Cooler
Install the 2 oil cooler hoses to the automatic transaxle assembly with the 2 clips.
7.INSTALL WIRE HARNESS CLAMP BRACKET
Install the 2 wire harness clamp brackets to the automatic transaxle assembly with the 2 bolts.
8.INSTALL WIRE HARNESS
Install the 2 wire harnesses to the automatic transaxle assembly with the 2 bolts.
30500
9.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY
Apply clutch spline grease to the contact surface between the crankshaft and torque converter assembly centerpiece.
Toyota Genuine Clutch Spline Grease or equivalent
About 1 g (0.0353 oz.)
Keeping the engine and automatic transaxle assembly in a horizontal position, align the knock pins with each hole on the automatic transaxle assembly and tighten the 11 bolts shown in the illustration.
(Bolt A)
(Bolt B)
(Bolt C)
(Bolt D)
Confirm that the 2 knock pins are on the transaxle fitted surface of the engine cylinder block before the transaxle installation.
Do not forcibly pry on the automatic transaxle assembly.
Check that the torque converter assembly rotates.
Bolt length:
55 mm (Bolt A)
50 mm (Bolt B)
41 mm (Bolt C)
33 mm (Bolt D)
Clean the installation holes for the torque converter assembly set bolts.
Apply a few drops of adhesive 1324 to 2 ore 3 threads of the 6 set bolts tip.
Tighten the 6 torque converter assembly set bolts.
First tighten the positioning bolt.
The positioning bolt is black.
Install the transmission breather skirt to the engine cylinder head with the bolt.
Install the breather plug hose to the transmission breather skirt with the clip.
11361J
10.INSTALL FLYWHEEL HOUSING UNDER COVER
Install the flywheel housing under cover with the 2 bolts.
28100
11.INSTALL STARTER ASSEMBLY
12.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
Install the engine assembly with transaxle (see page Engine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION).