Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › OIL PUMP
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292125 OIL PUMP A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL PUMP  REASSEMBLY  


PROCEDURE

Hide 35301A 1.INSTALL FRONT OIL PUMP OIL SEAL

a.
C138515E02
2.599,1.442 2.951,1.635 0.352,0.192 10 SST 2.546,1.515 1.74,1.022 false

Using SST and a hammer, install a new oil seal to the oil pump body.

SST
09350-32014  (09351-32140)

NOTICE:

The seal end should be level with the outer edge of the oil pump.



b.

Coat the lip of the oil seal with MP grease.


Hide 35301B 2.INSTALL FRONT OIL PUMP BODY O-RING

a.
C138278

Coat a new O-ring with ATF and install it to the oil pump body.

NOTICE:

Ensure that the O-ring is not twisted.



Hide 35322 3.INSTALL FRONT OIL PUMP DRIVEN GEAR

a.
C138277

Coat the front oil pump driven gear with ATF and install it to the oil pump body with the marked side up.


Hide 35321 4.INSTALL FRONT OIL PUMP DRIVE GEAR

a.
C138276

Coat the front oil pump drive gear with ATF, and install it to the oil pump body with the marked side up.


Hide 35370 5.INSTALL STATOR SHAFT ASSEMBLY

a.
C138275E04
1.448,2.604 1.594,2.771 0.146,0.167 10 false B 0.771,1.177 0.917,1.344 0.146,0.167 10 false A 1.021,0.604 1.167,0.771 0.146,0.167 10 false A 1.635,0.354 1.781,0.521 0.146,0.167 10 false A 2.26,0.542 2.406,0.708 0.146,0.167 10 false A 2.583,0.979 2.729,1.146 0.146,0.167 10 false A 2.552,1.615 2.698,1.781 0.146,0.167 10 false A 2.188,2.125 2.333,2.292 0.146,0.167 10 false A 1.708,2.229 1.854,2.396 0.146,0.167 10 false A 0.99,1.865 1.125,2.031 0.135,0.167 10 false A 2.219,2.813 2.365,2.979 0.146,0.167 10 false B 2.427,3.354 2.573,3.521 0.146,0.167 10 false B 2.375,4.052 2.521,4.219 0.146,0.167 10 false B 0.854,3.813 1,3.979 0.146,0.167 10 false B 0.927,3.083 1.073,3.25 0.146,0.167 10 false B 1.313,4.25 1.458,4.417 0.146,0.167 10 false B

Align each knock pin of the stator shaft with the holes in the oil pump body and install the stator shaft to the oil pump body with the 16 bolts.


b.

Using a "TORX" socket (T30), install the 11 bolts.

Torque:
9.3 N*m (95 kgf*cm, 82 in.*lbf)

- Bolt length
Bolt A 14 mm (0.55 in.)
Bolt B 26 mm (1.02 in.)


Hide 35035 6.INSPECT FRONT OIL PUMP AND GEAR BODY SUB-ASSEMBLY