Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL CASE › 2013.04–2014.09
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292127 DIFFERENTIAL CASE A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41331Q 1.INSTALL DIFFERENTIAL SIDE GEAR

a.
C138528

Coat the 2 front differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers with ATF and install them to the differential case.


Hide 41342F 2.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C138706

Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.


Hide 41342A 4.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C138707

Using a pin punch (3 mm) and hammer, install the pinion shaft straight pin.

NOTICE:

Align the holes, and install the pinion shaft straight pin.



b.
C138711

Using a chisel and hammer, stake the differential case.

NOTICE:

Stake the differential case after adjusting the backlash.



Hide 41311F 5.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C138712E03
2.331,0.52 2.683,0.697 0.352,0.178 10 SST 1.72,0.767 2.302,0.611 2.302,0.611 1.848,0.928 false

Using SST and a press, install the front differential case rear tapered roller bearing to the differential case.

SST
09726-36010  
09950-70010  (09951-07100)

NOTICE:

Do not damage the bearing cage during bearing inner race installation.



b.
C138714E04
1.49,0.875 2.458,1.552 2.458,1.552 1.719,1.354 true 2.5,1.5 2.833,1.792 0.333,0.292 10 true SST

Using SST and a hammer, install the front differential case rear tapered roller bearing outer race to the transaxle case.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the bearing and transaxle case.



Hide 41311E 6.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C366272E01
1.875,0.792 2.75,0.75 2.75,0.75 1.792,0.333 false 1.854,0.521 2.75,0.75 false 2.823,0.688 3.281,0.885 0.458,0.198 10 false SST

Using SST and a press, install the front differential case front tapered roller bearing to the differential case.

SST
09710-30012  (09710-04081)
09950-60010  (09951-00480)
09950-70010  (09951-07100)

NOTICE:

Do not damage the bearing cage during bearing inner race installation.



b.

Install the shim to the transaxle housing.


c.
C138715E01
2.693,1.444 2.998,1.606 0.305,0.162 10 SST 1.857,1.105 2.629,1.525 2.629,1.525 1.952,1.436 false

Using SST and a hammer, install the front differential case front tapered roller bearing outer race to the transaxle housing.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the bearing and transaxle housing.



Hide 7.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.
C136467

Install the differential assembly to the transaxle case.


b.

Clean the contact surfaces of the transaxle case and transaxle housing.


c.
C136447E13
2.921,0.092 3.052,0.245 0.132,0.152 10 A 2.503,1.866 2.634,2.018 0.132,0.152 10 B 1.51,1.618 2.486,1.958 2.486,1.958 2.219,1.657 false 1.905,1.645 2.486,1.958 false 0.385,0.161 0.517,0.313 0.132,0.152 10 A 3.088,1.029 3.220,1.181 0.132,0.152 10 A 0.516,1.783 0.648,1.935 0.132,0.152 10 A 1.212,1.952 1.344,2.104 0.132,0.152 10 A 2.584,0.92 3.062,1.106 3.062,1.106 2.508,1.416 false 3.062,1.106 2.617,1.149 false 2.032,0.602 2.895,0.191 2.895,0.191 2.298,0.742 false 1.796,0.505 2.879,0.198 false 1.28,1.948 1.313,1.737 false 1.354,0.438 0.553,0.273 0.553,0.273 0.848,0.717 false 1.148,0.511 0.553,0.273 0.553,0.273 1.025,0.614 false 0.087,1.267 0.218,1.420 0.132,0.152 10 A 0.593,1.021 0.229,1.351 0.229,1.351 0.675,1.607 false 0.57,1.399 0.229,1.351 0.229,1.351 0.544,1.198 false 0.871,1.757 0.658,1.875 0.658,1.875 1.088,1.806 false

Install the transaxle housing to the transaxle case with the 20 bolts.

Torque:
Bolt A : 31 N*m (316 kgf*cm, 23 ft.*lbf)
Bolt B : 23 N*m (234 kgf*cm, 17 ft.*lbf)


d.
C138262E06
0.841,4.027 1.204,4.212 0.364,0.184 10 SST 1.079,3.308 0.973,4.027 false

Using SST, turn the differential assembly right and left 2 or 3 times to settle the bearing.

SST
09564-33010  


e.

Using SST and a torque wrench, measure the turning torque of the differential side bearing while rotating SST at 10 rpm.

SST
09564-33010  

Turning torque:

1.05 to 1.93 N*m (10.70 to 19.67 kgf*cm, 9.29 to 17.08 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Shim thickness: mm (in.)
Thickness Thickness Thickness Thickness
2.000 (0.0787) 2.225 (0.0876) 2.450 (0.0965) 2.675 (0.1054)
2.025 (0.0797) 2.250 (0.0886) 2.475 (0.0974) 2.700 (0.1063)
2.050 (0.0807) 2.275 (0.0896) 2.500 (0.0984) 2.725 (0.1073)
2.075 (0.0817) 2.300 (0.0906) 2.525 (0.0994) 2.750 (0.1083)
2.100 (0.0827) 2.325 (0.0915) 2.550 (0.1004) 2.775 (0.1093)
2.125 (0.0837) 2.350 (0.0925) 2.575 (0.1014) 2.800 (0.1102)
2.150 (0.0847) 2.375 (0.0935) 2.600 (0.1024) 2.825 (0.1112)
2.175 (0.0856) 2.400 (0.0945) 2.625 (0.1034) 2.850 (0.1122)
2.200 (0.0866) 2.425 (0.0955) 2.650 (0.1043) 2.875 (0.1132)


f.
C136447

Remove the 20 bolts and the transaxle housing from the transaxle case.


g.
C136467

Remove the differential assembly from the transaxle case.


Hide 41221 8.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
D025215E22
0.792,0.031 2.833,0.208 2.042,0.177 10 false 90 to 110°C (194 to 230°F)

Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194.0 to 230.0°F).

NOTICE:

Do not heat the ring gear to more than 110°C (230.0°F).



b.

Clean the contact surface of the front differential case.


c.
C138531E12
1.26,1.438 1.021,0.604 1.021,0.604 1.177,1.5 true 0.396,0.406 1.208,0.573 0.813,0.167 10 false Matchmarks

Align the matchmarks, and install the front differential ring gear case quickly.

NOTICE:

Do not install the bolts while the ring gear is hot.



d.
C138532

Install and tighten the 12 bolts.

Torque:
120 N*m (1223 kgf*cm, 88 ft.*lbf)

NOTICE:

Tighten the bolts a little at a time in a diagonal sequence.



Hide 31105H 9.INSTALL TRANSAXLE CASE OIL SEAL

a.

Coat the lip of a new oil seal with MP grease.


b.
C138716E01
0.162,1.859 0.475,2.020 0.313,0.161 10 SST 1.43,1.212 0.529,1.928 0.529,1.928 1.354,1.527 false 2.743,1.386 3.056,1.547 0.313,0.161 10 SST 2.04,1.938 2.717,1.475 2.717,1.475 2.436,1.888 false

Using SST and a hammer, install the oil seal.

SST
09316-10010  
09950-70010  (09951-07100)

Oil seal drive in depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



Hide 31105D 10.INSTALL FRONT TRANSAXLE CASE OIL SEAL

a.

Coat the lip of a new oil seal with MP grease.


b.
C138717E01
0.112,2.398 0.431,2.577 0.319,0.179 10 SST 1.108,1.692 0.485,2.48 0.485,2.48 2.451,1.999 false

Using SST and a hammer, install the oil seal.

SST
09308-14010  

Oil seal drive in depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)