By switching the skid control ECU from normal mode to test mode, abnormality detection sensitivity is enhanced and troubleshooting can be conducted efficiently.
Perform a sensor check in the test mode after the speed sensor or sensor rotor has been repaired or replaced.
If the engine switch is turned from on (IG) to on (ACC) or off during test mode, DTCs related to the signal check function will be erased.
During test mode, the skid control ECU stores all DTCs related to the signal check function, and the DTCs are erased if normality is confirmed. Any remaining DTCs are those indicating abnormalities that were found.
CHECK SENSOR SIGNAL BY TEST MODE (When Using Intelligent Tester)
Procedures for test mode:
Turn the engine switch off.
Check that the steering wheel is in the centered position.
Check that the shift lever is in the P position and apply the parking brake.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Switch the skid control ECU to Test Mode using the intelligent tester. Enter the following menus: Chassis / ABS/VSC/TRC / Signal Check.
Check that the ABS warning light comes on for several seconds and then blinks in Test Mode.
If the ABS warning light does not blink, perform the relevant troubleshooting procedures. The relevant troubleshooting procedures are instructed in the sections listed in the table below.
| Section Title | See Procedure |
|---|---|
| ABS Warning Light does not Come ON | ( )
|
Start the engine.
Check the speed sensor.
Check the speed sensor signal.
Drive the vehicle straight forward at a speed of 100 km/h (62 mph) or more for several seconds.
Check that the ABS warning light goes off.
The speed sensor check may not be completed if the sensor check is started with the steering wheel turned or one or more wheels spinning.
If the speed sensor check is commenced while the steering wheel is turned, the ABS warning light may come on after the low speed check is finished.
The ABS warning light comes on immediately when an abnormality is detected.
The ABS warning light remains illuminated for the period of time between when the medium speed check finishes and the vehicle speed exceeds 55 km/h (34 mph), and for the period of time between when the high speed check finishes and the vehicle speed exceeds 100 km/h (62 mph).
If the sensor check finishes normally, after the high speed check, depressing the brake pedal turns the ABS warning light off.
If the sensor check does not finish normally, the ABS warning light continues the test mode blinking pattern.
Stop the vehicle.
End of the sensor check.
When the sensor check is successfully completed, the ABS warning light blinks in the test mode pattern when the vehicle is stopped, and goes off when the vehicle is driven.
If the sensor check is not completed, the ABS warning light blinks even while the vehicle is driven and the ABS does not operate.
Read the DTCs of the signal check function.
Read the DTC(s) by following the instructions on the tester screen.
See the list of DTCs (refer to the "DTC OF TEST MODE FUNCTION (SIGNAL CHECK)" table).
CHECK SENSOR SIGNAL BY TEST MODE (When not Using Intelligent Tester)
Procedures for test mode:
Turn the engine switch off.
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
Check that the steering wheel is in the centered position.
Check that the shift lever is in the P position and apply the parking brake.
Turn the engine switch on (IG).
Check that the ABS warning light comes on for several seconds and then blinks in Test Mode.
If the ABS warning light does not blink, perform the relevant troubleshooting procedures. The relevant troubleshooting procedures are instructed in the sections listed in the table below.
| Section Title | See Procedure |
|---|---|
| ABS Warning Light does not Come ON | ( )
|
| TS and CG Terminal Circuit | ( )
|
Start the engine.
Check the speed sensor.
Check the speed sensor signal.
Drive the vehicle straight forward at a speed of 100 km/h (62 mph) or more for several seconds, and then depress the brake pedal.
Check that the ABS warning light goes off.
If the low speed check and middle speed check finish normally, depressing the brake pedal will turn off the ABS warning light and permit ABS functions.
The speed sensor check may not be completed if the sensor check is started with the steering wheel turned or one or more wheels spinning.
If the speed sensor check is commenced while the steering wheel is turned, the ABS warning light may come on after the low speed check is finished.
The ABS warning light comes on immediately when an abnormality is detected.
When the speed sensor signal is normal, the ABS warning light goes off while driving at 100 km/h (62 mph) or more and blinks in the test mode pattern while stationary.
Do not drive the vehicle at a speed of 80 km/h (50 mph) or more after the ABS warning light turns off, because test mode DTCs are set again when the vehicle speed exceeds 80 km/h (50 mph).
Stop the vehicle.
End of the sensor check.
When the sensor check is successfully completed, the ABS warning light blinks in the test mode pattern when the vehicle is stopped, and goes off when the vehicle is driven.
If the sensor check is not completed, the ABS warning light blinks even while the vehicle is driving and the ABS does not operate.
Read the DTCs of the signal check function.
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the engine switch on (IG).
Count the number of blinks of the ABS warning light.
How to read DTCs:
Diagnostic trouble codes are represented by the number of blinks of a warning light. For example, code 21 would be shown by 2 blinks, a pause of 1.5 seconds, and then 1 blink.
If one code is detected:
The light repeats the same code after a pause of 4 seconds.
If multiple codes are detected:
The light outputs one code after another with a 2.5-second pause between each code. When all codes have been output, there is a 4-second pause and then the light begins to output the codes again.
If only DTCs are displayed, repair the malfunctioning area and clear the DTCs.
If DTCs and test mode codes (DTC of signal check function) are displayed, repair the malfunctioning area, clear the DTCs and perform the test mode inspection.
If more than 1 malfunction is detected at the same time, the lowest numbered code will be displayed first.
If DTCs or test mode codes are not displayed, the ABS warning light outputs the normal system code (the light comes on and goes off at 0.25 second intervals).
See the list of DTCs (refer to the "DTC OF TEST MODE FUNCTION (SIGNAL CHECK)" table).
If all sensors are normal, a normal system code is output (the light comes on and goes off at 0.25 second intervals).
After the check, disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the engine switch off.
DTC OF TEST MODE FUNCTION (SIGNAL CHECK)
| Code No. | Diagnosis | Trouble Areas |
|---|---|---|
| C1271/71 | Low output signal of front speed sensor RH | ·
Front speed sensor RH ·
Speed sensor circuit ·
Sensor installation |
| C1272/72 | Low output signal of front speed sensor LH | ·
Front speed sensor LH ·
Speed sensor circuit ·
Sensor installation |
| C1273/73 | Low output signal of rear speed sensor RH | ·
Skid control sensor RH ·
Speed sensor circuit ·
Sensor installation |
| C1274/74 | Low output signal of rear speed sensor LH | ·
Skid control sensor LH ·
Speed sensor circuit ·
Sensor installation |
| C1275/75 | Abnormal change in output signal of front speed sensor RH | ·
Sensor installation ·
Speed sensor rotor ·
Foreign matter on sensor tip or sensor rotor |
| C1276/76 | Abnormal change in output signal of front speed sensor LH | ·
Sensor installation ·
Speed sensor rotor ·
Foreign matter on sensor tip or sensor rotor |
| C1277/77 | Abnormal change in output signal of rear speed sensor RH | ·
Sensor installation ·
Speed sensor rotor ·
Foreign matter on sensor tip or sensor rotor |
| C1278/78 | Abnormal change in output signal of rear speed sensor LH | ·
Sensor installation ·
Speed sensor rotor ·
Foreign matter on sensor tip or sensor rotor |
The DTCs in this table are only output in test mode.
Detection of DTCs from C1271/71 to C1274/74 is completed before the vehicle speed reaches 5 km/h (3 mph).
Detection of DTCs from C1275/75 to C1278/78 is completed several seconds after the vehicle speed exceeds 45 km/h (28 mph).
C1271/71 - C1274/74: Speed output from only one wheel is extremely low despite other wheel speed outputs reaching 5 km/h (3 mph).
C1275/75 - C1278/78: Abnormal speed sensor output frequency is as shown in the illustration.