Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  U0073/94  Control Module Communication Bus OFF  U0100/65  Lost Communication with ECM / PCM  U0123/62  Lost Communication with Yaw Rate Sensor Module  U0126/63  Lost Communication with Steering Angle Sensor Module  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
U0073/94 When one of following conditions is met:
1.

With the IG1 terminal voltage 10 V or more, after the output of data from the skid control ECU is completed, the sending continues for 5 seconds or more.

2.

The condition that bus OFF state occurs once or more within 100 ms occurs 10 times in succession. (Sent signals cannot be received.)

3.

With the IG1 terminal voltage 10 V or more, a delay in receiving data from the yaw rate sensor and steering angle sensor continues for 1 second or more.

4.

With the IG1 terminal voltage 10 V or more, the condition that a delay in receiving data from the yaw rate sensor occurs more than once within 5 seconds occurs 10 times in succession.


CAN communication system
U0100/65 When either condition below is met:
1.

With the IG1 terminal voltage 10 V or more and the vehicle speed 9 mph (15 km/h) or more, data cannot be sent to the ECM for 2 seconds or more.

2.

With the IG1 terminal voltage 10 V or more and the vehicle speed 9 mph (15 km/h) or more for 2 seconds or more.


CAN communication system
(Skid control ECU to ECM)
U0123/62 When either condition below is met:
1.

With the IG1 terminal voltage 10 V or more, data from the deceleration sensor cannot be received for 1 second or more.

2.

With the IG1 terminal voltage 10 V or more, the following occurs 10 times in succession within 60 seconds.

(a)

The condition that data from the deceleration sensor cannot be received occurs once or more within 5 seconds.



CAN communication system
(Skid control ECU to yaw rate sensor)
U0126/63 When either of following conditions detected:
1.

When IG1 terminal voltage 10 V or more, data from steering angle sensor cannot be received for 1 second or more.

2.

When IG1 terminal voltage 10 V or more, following condition occurs 10 times in succession.


CAN communication system

CAUTION / NOTICE / HINT

The skid control ECU inputs the signals from the ECM, steering angle sensor, and yaw rate sensor via CAN communication system.

PROCEDURE

1.READ VALUE USING DATA LIST (MOMENTARY INTERRUPTION)
a.

Using the Data List of the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
EFI Communication Open EFI communication open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal
-
Steering Open Steering angle sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal
-
Yaw Rate Open Yaw rate sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal
-

Result
Condition Proceed to
There is a constant open circuit A
There are no momentary interruptions B
There are momentary interruptions C

HINT:

Perform the above inspection before removing the sensor and connector.




A

2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED

B

3.RECONFIRM DTC

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED
a.

Check if each sensor and ECM connector is securely connected.

OK:

The connector should be securely connected.




OK

3.RECONFIRM DTC

NG

CONNECT CONNECTOR TO EACH SENSOR OR ECM CORRECTLY

3.RECONFIRM DTC
a.

Record the output DTCs (for ABS, VSC and CAN communication) (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

HINT:

If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for ABS and VSC) after the CAN communication system returns to normal.


Result
Condition Proceed to
DTC for the CAN communication system is not output A
No DTC is output (ABS and/or VSC DTC are output) B
No DTC is output (No ABS and/or VSC DTC are output) C



A

B

REPAIR CIRCUIT INDICATED BY OUTPUT CODE

C

USE SIMULATION METHOD TO CHECK

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


b.

Check for any momentary interruption between the skid control ECU and each sensor or ECM (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).


c.

Check that there is no momentary interruption.



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC

b.

Turn the engine switch on (IG).


c.

Drive the vehicle and turn the steering wheel to the right and left at a speed of 9 mph (15 km/h) or more.


d.

Check that no CAN communication system DTC is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).


e.

If ABS and/or VSC DTCs are output, record them.

Result
Condition Proceed to
DTC for the CAN communication system is not output A
No DTC is output (ABS and/or VSC DTC are output) B
No DTC is output (No ABS and/or VSC DTC are output) C

HINT:

The CAN communication system must be normal when repairing the sensor DTCs (for ABS and VSC).




A

B

REPAIR CIRCUIT INDICATED BY OUTPUT CODE

C

END