Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2013.04–2016.05
RM24M0E _57 Power Source / Network _059598 CAN COMMUNICATION _0292257 CAN COMMUNICATION SYSTEM Y

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

NOTICE:
·

DTCs for the CAN communication system are as follows: U0073, U0100, U0101, U0121, U0123, U0126, U0129, U0140, U0155, U0182, U1002, B1207, B1216, B1217, B1287, B1499, B2326 and B2427.

·

Refer to the troubleshooting procedures of each system if DTCs regarding the CAN communication system are not output.

·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the engine switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:
·

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Use the intelligent tester.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding.

Result:
Proceed to
NEXT



NEXT

3.CHECK AND CLEAR DTCS*
3.CHECK AND CLEAR DTCS*
a.

Using the intelligent tester, perform the ALL DTC check.

NOTICE:
·

If a CAN communication malfunction code that informs that an ECU or sensor has a power malfunction or internal malfunction is causing a communication stop, the malfunction may not be in the communication line. There is a high possibility that the ECU or sensor has a signal transmission failure. Therefore, first troubleshoot any DTCs related to the ECU or sensor.

·

When CAN communication related connectors are disconnected with the engine switch on (IG or ACC), the ECU related to the connector and ECUs of related systems will store a CAN communication DTC.




Result:
Proceed to
NEXT



NEXT

4.CHECK INSTALLED SYSTEMS (ECU AND SENSOR) THAT USE CAN COMMUNICATION
4.CHECK INSTALLED SYSTEMS (ECU AND SENSOR) THAT USE CAN COMMUNICATION
a.

Based on the vehicle equipment and specifications, confirm the systems that use CAN communication (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


Result:
Proceed to
NEXT



NEXT

5.CHECK ECUS CONNECTED TO CAN BUS (USING INTELLIGENT TESTER)*
5.CHECK ECUS CONNECTED TO CAN BUS (USING INTELLIGENT TESTER)*
a.

Select "Bus Check" from the "System Select" screen on the intelligent tester (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


b.

Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter" (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


c.

Wait 1 minute and then check the display of the connected ECUs and sensors.

Result:
Inspection Result Proceed to
No ECUs or sensors are displayed (CAN No. 1 bus circuit main wire open or short malfunction, or DLC3 branch wire malfunction). A
Except for main body ECU, no ECUs connected to CAN MS bus circuit are displayed. Main body ECU outputs CAN MS bus circuit malfunction code (B2326) (CAN MS bus circuit main wire open or short malfunction). B
No ECUs connected to CAN MS bus circuit are displayed (branch wire between main body ECU and CAN No. 1 bus circuit is open). C
Except for network gateway ECU, no ECUs connected to CAN No. 2 bus circuit are displayed (CAN No. 2 bus circuit main wire open or short malfunction). D*
No ECUs connected to CAN No. 2 bus circuit are displayed (branch wire between network gateway ECU and CAN No. 1 bus circuit is open). E*
ECU or sensor that should be connected to CAN communication is not displayed (ECU or sensor branch wire open). F
ECU or sensor that should be connected to CAN communication is not displayed or display is intermittent during check (ECU or sensor branch wire open on one side). G
All ECUs and sensors connected to CAN communication system displayed on screen. H


NOTICE:
·

ECUs and sensors that are not present will not be displayed. Be careful not to mistake them for communication stop malfunctions.



HINT:
·

*: This applies only for RHD models.

·

If the display of an ECU is intermittent during the check, one side of an ECU or sensor branch wire is open. (The signal of the ECU is treated as noise, which affects the response and display of the intelligent tester.)

·

The main body ECU checks for proper ECU communication for ECUs that are connected to the CAN MS bus circuit, and the results are displayed on the intelligent tester. The network gateway ECU checks for proper ECU communication for ECUs that are connected to the CAN No. 2 bus circuit, and the results are displayed on the intelligent tester. If communication stops between an ECU and the main body ECU or network gateway ECU for 10 seconds or more, the ECU disappears from the intelligent tester display.

·

For communication stop mode of ECUs connected to the CAN MS bus circuit and CAN No. 2 bus circuit, refer to the DTC of the respective communication stop.





A

6.CHECK DLC3 BRANCH WIRE AND CAN NO. 1 BUS CIRCUIT MAIN WIRE (CANH - CANL)

B

GO TO DTC B2326

C

GO TO MAIN BODY ECU COMMUNICATION STOP MODE

D*

GO TO DTC U1002

E*

GO TO GATEWAY ECU COMMUNICATION STOP MODE

F

GO TO PROBLEM SYMPTOMS TABLE

G

GO TO OPEN IN ONE SIDE OF CAN BRANCH WIRE

H

9.CHECK COMMUNICATION MALFUNCTION DTC (PAST DTC CHECK)*
6.CHECK DLC3 BRANCH WIRE AND CAN NO. 1 BUS CIRCUIT MAIN WIRE (CANH - CANL)
a.
H103119E01
1.958,0.938 2.26,0.552 false 1.896,1.823 1.938,1.458 false 2.333,0.438 2.948,0.635 0.615,0.198 10 false CANH 1.677,1.844 2.292,2.042 0.615,0.198 10 false CANL

Measure the resistance of the DLC3.

Standard resistance:
Tester Connection Condition Specified Condition
6 (CANH) - 14 (CANL) Engine switch off 54 to 69 Ω


Result:
Result Proceed to
OK A
NG (70 Ω or higher) B
NG (Below 54 Ω) C




A

7.CHECK CAN NO. 1 BUS CIRCUIT GND (CANH, CANL - CG)

B

GO TO CAN MAIN WIRE FOR DISCONNECTION

C

GO TO CHECK CAN BUS LINES FOR SHORT CIRCUIT

7.CHECK CAN NO. 1 BUS CIRCUIT GND (CANH, CANL - CG)
a.
H103119E02
1.958,0.938 2.26,0.552 false 1.896,1.823 1.938,1.458 false 1.594,0.938 1.208,0.531 false 2.313,0.438 2.927,0.635 0.615,0.198 10 false CANH 1.677,1.844 2.292,2.042 0.615,0.198 10 false CANL 0.948,0.438 1.563,0.635 0.615,0.198 10 false CG

Measure the resistance of the DLC3.

Standard resistance:
Tester Connection Condition Specified Condition
6 (CANH) - 4 (CG) Engine switch off 200 Ω or higher
14 (CANL) - 4 (CG) Engine switch off 200 Ω or higher



Result:
Proceed to
OK
NG



OK

8.CHECK CAN NO. 1 BUS CIRCUIT +B (CANH, CANL - BAT)

NG

GO TO CHECK CAN BUS LINE FOR SHORT TO GND

8.CHECK CAN NO. 1 BUS CIRCUIT +B (CANH, CANL - BAT)
a.

Disconnect the Cable from negative (-) battery terminal.


b.
H103119E03
1.958,0.938 2.26,0.552 false 1.896,1.823 1.938,1.458 false 2.583,1.781 2.365,1.469 false 2.333,0.438 2.948,0.635 0.615,0.198 10 false CANH 1.677,1.844 2.292,2.042 0.615,0.198 10 false CANL 2.51,1.833 3.125,2.031 0.615,0.198 10 false BAT

Measure the resistance of the DLC3.

Standard resistance:
Tester Connection Condition Specified Condition
6 (CANH) - 16 (BAT) Cable is disconnected from negative (-) battery terminal 6 kΩ or higher
14 (CANL) - 16 (BAT) Cable is disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK COMMUNICATION MALFUNCTION DTC (PAST DTC CHECK)*

NG

GO TO CHECK CAN BUS LINE FOR SHORT TO +B

9.CHECK COMMUNICATION MALFUNCTION DTC (PAST DTC CHECK)*
a.

Select "Bus Check" from the "System Select" screen on the intelligent tester (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


b.

Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter" (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


c.

Write down all of the DTCs stored in each ECU.

HINT:
·

If there are communication malfunction DTCs stored but the intelligent tester's "Bus Check - Communication Bus Check" screen displays all of the ECUs and sensors connected to the CAN system, the communication malfunction DTCs may be past malfunctions that are no longer present.

·

For CAN No. 1 bus circuit main wire malfunctions, related ECUs are also detected. Therefore, determine the malfunctioning area based on all of the DTCs that are output.

·

For CAN MS bus circuit malfunctions, DTCs are output based on the detection of communication stop malfunctions and network malfunctions of ECUs that are connected by the main body ECU.

·

*: For CAN No. 2 bus circuit malfunctions, DTCs are output based on the detection of communication stop malfunctions of ECUs that are connected by the network gateway ECU (for RHD).

·

*1: This applies only for RHD models.

·

*: During a network malfunction (main wire malfunction), the network gateway ECU may erase stored DTCs in an attempt to reinstate communication (for RHD).

·

*: For DTCs regarding connected ECUs that are output when the CAN No. 2 bus circuit main wire is malfunctioning, refer to the DTC COMBINATION TABLE (Can No. 2 Bus Circuit Main Wire Past Malfunction) (for RHD).



Result:
Inspection Result Proceed to
ECU connected to CAN No. 1 bus circuit main wire has stored communication malfunction code (Can No. 1 bus circuit main wire past malfunction). A
Main body ECU outputs CAN MS bus circuit malfunction code (B2326) (CAN MS bus circuit past malfunction) B
Main body ECU outputs malfunction code other than CAN MS bus circuit malfunction code (B2326) (past malfunction of ECU branch wire connected to CAN MS bus circuit) C
Except for network gateway ECU, ECUs connected to CAN No. 2 bus circuit output all DTCs (all communication stop) Network gateway ECU outputs network malfunction code (U1002) (CAN No. 2 bus circuit past malfunction) D*1
Network gateway ECU outputs malfunction code other than network malfunction code (U1002) (past malfunction of branch wire connected to CAN No. 2 bus circuit) E*1




A

10.CHECK DTC COMBINATION TABLE (CAN NO. 1 BUS CIRCUIT BRANCH WIRE OPEN PAST MALFUNCTION)

B

GO TO DTC B2326

C

GO TO PROBLEM SYMPTOMS TABLE

D*1

GO TO DTC U1002

E*1

GO TO PROBLEM SYMPTOMS TABLE

10.CHECK DTC COMBINATION TABLE (CAN NO. 1 BUS CIRCUIT BRANCH WIRE OPEN PAST MALFUNCTION)
a.

Based on the combination of stored CAN communication system DTCs, determine which ECUs and sensors have a communication stop malfunction (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


Result:
Proceed to
NEXT



NEXT

11.PERFORM MALFUNCTION SIMULATION TEST (CAN NO. 1 BUS CIRCUIT MAIN WIRE PAST MALFUNCTION)
11.PERFORM MALFUNCTION SIMULATION TEST (CAN NO. 1 BUS CIRCUIT MAIN WIRE PAST MALFUNCTION)
a.

Using the intelligent tester, clear all DTCs.


b.

Perform a malfunction simulation test on all harnesses and connectors related to the CAN No. 1 bus circuit main wire.


c.

Check the DTCs that were output as a result of the malfunction simulation test. Then determine the malfunctioning area.


Result:
Proceed to
NEXT



NEXT

12.ADJUST, REPAIR AND REPLACE
12.ADJUST, REPAIR AND REPLACE
Result:
Proceed to
NEXT



NEXT

13.CONFIRMATION TEST
13.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END