By switching the skid control ECU from normal mode to test mode, abnormality detection sensitivity is enhanced and troubleshooting can be conducted efficiently.
Perform a sensor check in test mode after the speed sensor or sensor rotor has been repaired or replaced.
If the engine switch is turned from on (IG) to on (ACC) or off during test mode, DTCs related to the signal check function will be erased.
DTCs are stored if any malfunctions are detected during the check of each sensor.
CHECK SENSOR SIGNAL BY TEST MODE (When Using Intelligent Tester)
Procedures for test mode:
Turn the engine switch off.
Check that the steering wheel is in the centered position.
Check that the shift lever is in the P position and apply the parking brake.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Switch the skid control ECU to Test Mode using the intelligent tester. Enter the following menus: Chassis / ABS/VSC/TRC / Signal Check.
Check that the ABS warning and slip indicator lights come on for several seconds and then blink in Test Mode.
If the ABS warning and slip indicator lights do not blink, check the ABS warning and slip indicator light circuits.
| Section Title | See procedure |
|---|---|
| ABS Warning Light does not Come ON | ( )
|
| Slip Indicator Light does not Come ON | ( )
|
Start the engine.
Check the lost booster pressure judgment.
Perform the check in the lost booster pressure state (negative pressure in the booster is depressurized).
Turn the engine switch on (IG).
Check that the brake warning light comes on when depressing the brake pedal with a force of 59 N (6 kgf, 13.2 lbf) or more for 1 second or more. (The lost booster pressure state is judged to be normal.)
Start the engine depressing the brake pedal with a force of 59 N (6 kgf, 13.2 lbf) or more for 1 second or more.
Check that the brake warning light goes off when quickly releasing the brake pedal. (The lost booster pressure state is judged to be normal.)
If the lost booster pressure state is not judged to be normal, the brake warning light blinks continuously and DTC ABS81 (C1281) is recorded.
Leave the vehicle as is for 1 second or more.
If you slowly depress the brake pedal or depress it again, master cylinder pressure sensor zero point calibration is not performed normally.
If the lost booster pressure judgment check is not completed normally, the master cylinder pressure sensor check is not judged.
If a recheck is performed after the engine has started, end the Test Mode, enter Test Mode again, and release the vacuum in the booster by pumping the brake pedal prior to the recheck.
Check the speed sensor.
Check the speed sensor signal.
Drive the vehicle straight forward at a speed of 45 km/h (28 mph) or more for several seconds.
Check that the ABS warning light goes off.
The speed sensor check may not be completed if the sensor check is started with the steering wheel turned or one or more wheels spinning.
If the speed sensor check is commenced while the steering wheel is turned, the ABS warning light may come on after the low speed check is finished.
The ABS warning light comes on immediately when an abnormality is detected.
After the ABS warning light goes off, if the vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
Stop the vehicle.
Check the VSC OFF switch.
Check that the TRC OFF indicator light comes on.
Check that the VSC OFF indicator light goes off.
Perform either of the following to inspect the VSC OFF switch.
Check that the TRC OFF indicator light changes from on to off when the VSC OFF switch is pressed but not held for 3 seconds or more.
Check that the VSC OFF indicator light changes from off to on when the VSC OFF switch is pressed and held for 3 seconds or more.
Check the end of sensor.
When the sensor check is successfully completed, the ABS warning light blinks in the test mode pattern when the vehicle is stopped, and goes off when the vehicle is driven.
If the sensor check is not completed, the ABS warning light blinks even while the vehicle is driving and the ABS does not operate.
Read the DTCs of signal check function.
Read the DTC(s) by following the instructions on the tester screen.
If only the DTCs are displayed, repair the malfunction area and clear the DTCs.
If the DTCs or Test Mode codes (DTC of signal check function) are displayed, repair the malfunction area, clear the DTCs and perform the Test Mode inspection.
See the list of the DTCs (refer to "DTC OF TEST MODE FUNCTION (SIGNAL CHECK)" below).
CHECK SENSOR SIGNAL BY TEST MODE (When not Using Intelligent Tester)
Procedures for test mode:
Turn the engine switch off.
Check that the steering wheel is in the centered position.
Check that the shift lever is in the P position and apply the parking brake.
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
Turn the engine switch on (IG).
Check that the ABS warning and slip indicator lights come on for several seconds and then blink in Test Mode.
If the ABS warning and slip indicator lights do not blink, inspect the TS and CG terminal circuit and ABS warning and slip indicator light circuits.
| Section Title | See procedure |
|---|---|
| ABS Warning Light does not Come ON | ( )
|
| Slip Indicator Light does not Come ON | ( )
|
| TS and CG Terminal Circuit | ( )
|
Start the engine.
Check the lost booster pressure judgment.
Perform the check in the lost booster pressure state (negative pressure in the booster is depressurized).
Turn the engine switch on (IG).
Check that the brake warning light comes on when depressing the brake pedal with a force of 59 N (6 kgf, 13.2 lbf) or more for 1 second or more. (The lost booster pressure state is judged to be normal.)
Start the engine depressing the brake pedal with a force of 59 N (6 kgf, 13.2 lbf) or more for 1 second or more.
Check that the brake warning light goes off when quickly releasing the brake pedal. (The lost booster pressure state is judged to be normal.)
If the lost booster pressure state is not judged to be normal, the brake warning light blinks continuously and DTC ABS81 (C1281) is recorded.
Check the speed sensor.
Check the speed sensor signal.
Drive the vehicle straight forward at a speed of 45 km/h (28 mph) or more for several seconds.
Check that the ABS warning light goes off.
If the sensor check does not finish normally, the ABS warning light continues the test mode blinking pattern.
The speed sensor check may not be completed if the sensor check is started with the steering wheel turned or one or more wheels spinning.
If the speed sensor check is commenced while the steering wheel is turned, the ABS warning light may come on after the low speed check is finished.
The ABS warning light comes on immediately when an abnormality is detected.
After the ABS warning light goes off, if the vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
Stop the vehicle.
Check the VSC OFF switch.
Check that the TRC OFF indicator light comes on.
Check that the VSC OFF indicator light goes off.
Perform either of the following to inspect the VSC OFF switch.
Check that the TRC OFF indicator light changes from on to off when the VSC OFF switch is pressed but not held for 3 seconds or more.
Check that the VSC OFF indicator light changes from off to on when the VSC OFF switch is pressed and held for 3 seconds or more.
Check the end of the sensor.
When the sensor check is successfully completed, the ABS warning light blinks in the test mode pattern when the vehicle is stopped, and goes off when the vehicle is driven.
If the sensor check is not completed, the ABS warning light blinks even while the vehicle is driving and the ABS does not operate.
Read the DTCs of the signal check function.
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the engine switch on (IG).
Count the number of blinks of the ABS warning and slip indicator lights.
How to read DTCs:
Diagnostic trouble codes are represented by the number of blinks of a warning light. For example, code 21 would be shown by 2 blinks, a pause of 1.5 seconds, and then 1 blink.
If one code is detected:
The light repeats the same code after a pause of 4 seconds.
If multiple codes are detected:
The light outputs one code after another with a 2.5-second pause between each code. When all codes have been output, there is a 4-second pause and then the light begins to output the codes again.
If only DTCs are displayed, repair the malfunctioning area and clear the DTCs.
If the DTCs or test mode codes (DTC of signal check function) are displayed, repair the malfunctioning area, clear the DTCs and perform the test mode inspection.
If more than 1 malfunction is detected at the same time, the lowest numbered code will be displayed first.
If DTCs or test mode codes are not displayed, the ABS warning light outputs the normal system code (the light comes on and goes off at 0.25 second intervals).
See the list of DTCs (refer to "DTC OF TEST MODE FUNCTION (SIGNAL CHECK)" below).
If all sensors are normal, a normal system code is output (the light comes on for 0.25 seconds at intervals of 0.25 seconds).
After the check, disconnect SST from terminals TC and CG of DLC3.
Turn the engine switch off.
DTC OF TEST MODE FUNCTION (SIGNAL CHECK)
| DTC No. | Diagnosis | Trouble Areas |
|---|---|---|
| C1271/71 | Low output signal of front speed sensor RH | ·
Front speed sensor RH ·
Speed sensor circuit ·
Sensor installation |
| C1272/72 | Low output signal of front speed sensor LH | ·
Front speed sensor LH ·
Speed sensor circuit ·
Sensor installation |
| C1273/73 | Low output signal of rear speed sensor RH | ·
Rear speed sensor RH ·
Speed sensor circuit ·
Sensor installation |
| C1274/74 | Low output signal of rear speed sensor LH | ·
Rear speed sensor LH ·
Speed sensor circuit ·
Sensor installation |
| C1275/75 | Abnormal change in output signal of front speed sensor RH | ·
Sensor installation ·
Speed sensor rotor ·
Foreign matter on sensor tip or sensor rotor |
| C1276/76 | Abnormal change in output signal of front speed sensor LH | ·
Sensor installation ·
Speed sensor rotor ·
Foreign matter on sensor tip or sensor rotor |
| C1277/77 | Abnormal change in output signal of rear speed sensor RH | ·
Sensor installation ·
Speed sensor rotor ·
Foreign matter on sensor tip or sensor rotor |
| C1278/78 | Abnormal change in output signal of rear speed sensor LH | ·
Sensor installation ·
Speed sensor rotor ·
Foreign matter on sensor tip or sensor rotor |
| C1281/81 | Master cylinder pressure sensor output malfunction | ·
Master cylinder pressure sensor ·
Brake pedal load sensing switch (w/o Mechanical brake assist) |
The DTCs in this table are only output in Test Mode.
The detection of DTCs from C1271/71 to C1274/74 is completed before the vehicle speed reaches 5 km/h (3 mph).
The detection of DTCs from C1275/75 to C1278/78 is completed before the vehicle speed reaches 45 km/h (28 mph).
C1271/71 to C1274/74: The speed output from only one wheel is extremely low despite other wheel speed outputs reaching 5 km/h (3 mph).
C1275/75 to C1278/78: The abnormal speed sensor output frequency is as shown in the illustration.