Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TS and CG Terminal Circuit  


DESCRIPTION

If the vehicle is stationary during sensor check mode, speed sensor malfunctions cannot be detected. The vehicle must be driven for speed sensor malfunctions to be detected.

HINT:

Change to sensor check mode by connecting terminals TC and CG of the DLC3, and turning the engine switch from off to on (IG).


WIRING DIAGRAM

C142153E05
5.76,3.76 6.875,4.104 1.115,0.344 10 false A9 6.01,0.906 6.313,1.125 0.302,0.219 10 false TS 1.073,0.906 1.375,1.125 0.302,0.219 10 false TS 1.052,1.99 1.354,2.208 0.302,0.219 10 false CG 0.677,3.792 1.281,4.125 0.604,0.333 10 false G15 5.729,1.073 5.958,1.292 0.229,0.219 10 false 16 1.438,1.042 1.677,1.229 0.24,0.188 10 false 12 1.417,2.125 1.656,2.313 0.24,0.188 10 false 4 0.677,3.958 1.281,4.292 0.604,0.333 10 false DLC3 5.771,3.938 6.885,4.281 1.115,0.344 10 false Skid Control ECU

PROCEDURE

1.CHECK WIRE HARNESS (DLC3 - SKID CONTROL ECU AND BODY GROUND)
a.
U189401E02
1.594,1.365 1.74,1.042 false 1.594,1.958 1.865,2.271 false 2.281,3.396 2.583,3.906 false 0.083,0.021 1.406,0.24 1.323,0.219 10 false Wire Harness Side: 0.125,0.74 0.458,0.896 0.333,0.156 10 false G15 0.281,2.615 0.573,2.771 0.292,0.156 10 false A9 1.156,2.531 2.302,2.708 1.146,0.177 10 false Skid Control ECU 0.885,0.604 1.281,0.75 0.396,0.146 10 false DLC3 1.792,0.875 2.031,1.021 0.24,0.146 10 false CG 1.875,2.188 2.083,2.354 0.208,0.167 10 false TS 2.573,3.927 2.781,4.094 0.208,0.167 10 false TS

Disconnect the A9 ECU connector.


b.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G15-4 (CG) - Body ground Below 1 Ω
G15-12 (TS) - A9-16 (TS) Below 1 Ω
A9-16 (TS) - Body ground 10 kΩ or higher

Result
Result Proceed to
OK (for 2AZ-FE) A
OK (for 2GR-FE) B
NG C




A

B

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR