Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1241  Low Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation. This DTC is stored when the +BS terminal voltage deviates due to a malfunction in the power supply or charging circuit such as the battery or alternator circuit, etc. The DTC is cleared when the +BS terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1241 Low Power Supply Voltage Malfunction Any of the following is detected:
1.

The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (soft low voltage) is less than 9.6 V for 1 second or more.

2.

The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (hard low voltage) is less than 6.9 V for 1 second or more.

3.

The vehicle speed is 15 km/h (9 mph) or more, the +BS terminal voltage is 9.6 V or more, the skid control ECU (brake actuator assembly) turns on more than one valve at the same time within a short period of time and the valve relay supply voltage drop exceeds the threshold.*

4.

The +BS terminal voltage is less than 6.7 V and the skid control ECU (brake actuator assembly) judges that power supply voltage is abnormal for 0.06 seconds or more.


·

ABS NO. 2 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Ground circuit

·

Internal power supply circuit of the skid control ECU (brake actuator assembly)



*: The skid control ECU (brake actuator assembly) monitors the resistance of the power source line at the +BS terminal. A malfunction is detected when an abnormality occurs in the +BS terminal wire harness or its connection and the skid control ECU (brake actuator assembly) determines that the wiring resistance at the +BS terminal exceeds the standard resistance.

WIRING DIAGRAM

C313365E02
2.073,1.542 3.073,1.75 1,0.208 10 false LH-IG Relay2 4.01,0.885 5.01,1.094 1,0.208 10 false GAUGE NO. 1 6.198,0.708 6.563,0.917 0.365,0.208 10 false IG1 5.917,0.583 6.281,0.792 0.365,0.208 10 false 28 6.188,3.906 6.552,4.115 0.365,0.208 10 false +BS 5.927,3.792 6.292,4 0.365,0.208 10 false 25 6.198,6.802 6.698,7.01 0.5,0.208 10 false GND1 5.927,6.677 6.292,6.885 0.365,0.208 10 false 38 0.5,3.083 0.771,3.292 0.271,0.208 10 false 1G 0.854,3.073 1.125,3.281 0.271,0.208 10 false 1 0.854,5.813 1.125,6.021 0.271,0.208 10 false 1 0.729,2.677 3.854,2.885 3.125,0.208 10 false Engine Room NO. 1 Relay Block, Junction Block 0.688,3.5 1.688,3.708 1,0.208 10 false LH-MAIN-JB 1.01,4.063 2.01,4.271 1,0.208 10 false F/B ALT 1.948,4.063 2.948,4.271 1,0.208 10 false ABS NO. 2 0.51,5.823 0.781,6.031 0.271,0.208 10 false 1A 1.583,5.375 1.854,5.583 0.271,0.208 10 false 1C 3.427,3.906 3.698,4.115 0.271,0.208 10 false 1 2.052,3.781 2.323,3.99 0.271,0.208 10 false 1 2.469,3.781 2.74,3.99 0.271,0.208 10 false 2 1.635,5.156 1.906,5.365 0.271,0.208 10 false 1 0.781,5.458 1.781,5.667 1,0.208 10 false F/B BATT 0.688,4.719 1.688,4.927 1,0.208 10 false ALT 1.979,5.521 2.979,5.729 1,0.208 10 false AM2 NO. 2 2.198,5.26 2.469,5.469 0.271,0.208 10 false 1 2.604,5.26 2.875,5.469 0.271,0.208 10 false 2 2.979,5.375 3.375,5.583 0.396,0.208 10 false G57 3.406,5.375 3.802,5.583 0.396,0.208 10 false AM1 3.406,6.063 3.802,6.271 0.396,0.208 10 false AM2 3.073,5.156 3.344,5.365 0.271,0.208 10 false 6 4.5,5.385 4.896,5.594 0.396,0.208 10 false G57 4.594,5.167 4.865,5.375 0.271,0.208 10 false 3 2.979,6.083 3.375,6.292 0.396,0.208 10 false G58 3.073,5.854 3.344,6.063 0.271,0.208 10 false 1 4.042,5.375 4.438,5.583 0.396,0.208 10 false IG1D 0.688,6.396 1.688,6.604 1,0.208 10 false FL MAIN 0.813,7.24 1.813,7.448 1,0.208 10 false Battery 3.073,6.729 4.885,7.115 1.813,0.385 10 false Main Body ECU (Instrument Panel Junction Block LH) 5.552,8.031 7.125,8.417 1.573,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 5.229,8.031 5.729,8.24 0.5,0.208 10 false A35

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
U189562E02
1.208,1.521 1.542,0.781 false 2.75,1.479 2.958,0.729 false 0.344,2.677 0.677,1.583 false 0.271,0.177 0.469,0.333 0.198,0.156 10 false *a 0.229,0.781 0.521,0.938 0.292,0.156 10 false A35 1.469,0.583 1.76,0.74 0.292,0.156 10 false IG1 0.177,2.698 0.469,2.854 0.292,0.156 10 false +BS 2.729,0.552 3.156,0.708 0.427,0.156 10 false GND1

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-25 (+BS) - Body ground Always 11 to 14 V
A35-25 (+BS) - A35-38 (GND1) Always 11 to 14 V
A35-28 (IG1) - Body ground Engine switch on (IG) 11 to 14 V
A35-28 (IG1) - A35-38 (GND1) Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Result Proceed to
OK A
NG (for +BS circuit) B
NG (for IG1 circuit) C



A

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

B

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
U189563E02
2.729,1.5 2.292,0.771 false 0.271,0.198 0.469,0.354 0.198,0.156 10 false *a 0.24,0.792 0.531,0.948 0.292,0.156 10 false A35 2.031,0.594 2.49,0.75 0.458,0.156 10 false GND1

Turn the engine switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-38 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

4.RECONFIRM DTC
a.

Reconnect the A35 skid control ECU (brake actuator assembly) connector.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1241 is not output. A
DTC C1241 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK)
a.

Turn the engine switch off.


b.

Disconnect the 1A engine room NO. 1 relay block, junction block connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-25 (+BS) - 1A-1 Always Below 1 Ω


HINT:
·

Even if the resistance between the skid control ECU (brake actuator assembly) and the engine room NO. 1 relay block, junction block is normal, there may be an abnormality in the resistance of the wiring between the battery and the engine room NO. 1 relay block, junction block.

Therefore, be sure to inspect the circuit between the battery and the engine room NO. 1 relay block, junction block before replacing the skid control ECU (brake actuator assembly).

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).





OK

NG

REPAIR OR REPLACE WIRE HARNESS OR ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK