Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR(w/ VSC) › from 2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292165 BRAKE ACTUATOR(w/ VSC) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(w/ VSC)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 55712 4.REMOVE FRONT COWL TOP OUTSIDE PANEL WITH WINDSHIELD WIPER MOTOR AND LINK

Hide 17705 5.REMOVE AIR CLEANER CAP SUB-ASSEMBLY (for 2AZ-FE)

Hide 17700 6.REMOVE AIR CLEANER CASE SUB-ASSEMBLY (for 2AZ-FE)

Hide 11209 7.REMOVE V-BANK COVER SUB-ASSEMBLY (for 2GR-FE)

Hide 17705 8.REMOVE AIR CLEANER CAP SUB-ASSEMBLY (for 2GR-FE)

Hide 17700 9.REMOVE AIR CLEANER CASE SUB-ASSEMBLY (for 2GR-FE)

Hide 10.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C307837E02
1.146,1.167 1.323,1.344 0.177,0.177 10 true *b 1.292,0.24 1.469,0.417 0.177,0.177 10 true *d 2.135,0.271 2.313,0.448 0.177,0.177 10 true *f 2.115,1.156 2.292,1.333 0.177,0.177 10 true *a 1.083,0.271 1.26,0.448 0.177,0.177 10 true *c 1.896,0.229 2.073,0.406 0.177,0.177 10 true *e

Use tags or make a memo to identify the places to reconnect the brake lines.

Text in Illustration
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


b.

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.


c.
C302801E02
1.24,1.208 1.406,1.385 0.167,0.177 10 true A 1.333,2.698 1.5,2.875 0.167,0.177 10 true B

Disengage the claw (A) and raise the lock lever.


d.

Engage the claw (B) and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



e.
C302803

Disengage the wire harness clamp from the brake actuator bracket assembly.


f.
C302804

Disengage the tube clamp from the brake actuator bracket assembly.


g.

Remove the 3 nuts and brake actuator with bracket.

NOTICE:

Do not kink or damage the brake lines.


HINT:

Remove the brake actuator with bracket while avoiding the brake lines.



Hide 44510 11.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C302805

Loosen the 3 nuts and brake actuator assembly from the brake actuator bracket assembly.