The skid control ECU (brake actuator assembly) acquires the steering angle sensor zero point every time the engine switch is turned on (IG) and the vehicle is driven at 50 km/h (31 mph) or more for approximately 30 seconds. The ECU also stores previous zero points.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1439 | Steering Angle Sensor Initialization Incomplete | After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the power source, the steering angle sensor zero point calibration cannot be obtained for 115 seconds of continuous driving. | ·
Steering angle sensor ·
Yaw rate and acceleration sensor |
| C1445 | Vehicle Driven with Steering Angle Sensor not Initialized | Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record of steering angle sensor zero point calibration at a speed of 15 km/h (9 mph) or more for 115 seconds or more without the brake pedal being depressed. | ·
Steering angle sensor ·
Yaw rate and acceleration sensor |
Because this DTC is related to a temporary loss of steering angle zero point calibration, before proceeding with the inspection, it is useful to confirm whether the power source voltage was interrupted by an operation such as removal or disconnection of the battery.
When DTC U0073, U0123 and/or U0126 is output together with DTC C1439 and/or C1445, inspect and repair the trouble areas indicated by DTC U0073, U0123 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073).
When a speed sensor or the yaw rate and acceleration sensor is malfunctioning, DTCs for the steering angle sensor may be stored even when the steering angle sensor is normal. When DTCs for a speed sensor or yaw rate and acceleration sensor are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor or yaw rate and acceleration sensor first, and then inspect and repair the steering angle sensor.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Turn the engine switch on (IG) again and check that no CAN communication system DTCs are output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
Drive the vehicle at a speed of 50 km/h (31 mph) and turn the steering wheel to the right and left and check that no speed sensor or yaw rate and acceleration sensor DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1439 and/or C1445 are output. | A |
| CAN communication system DTCs are output. | B |
| Speed sensor and/or yaw rate and acceleration sensor DTCs are output. | C |
| DTCs C1439 and C1445 are not output. | D |
If a speed sensor or the yaw rate and acceleration sensor is malfunctioning, DTCs for the steering angle sensor may be stored even though the steering angle sensor is normal.
If speed sensor and yaw rate and acceleration sensor DTCs are output simultaneously, repair these malfunctions and then inspect the steering angle sensor.
If DTC C1439 and/or C1445 is not output again, the DTC may have been stored due to a temporary loss of steering angle zero point calibration, such as a loss of calibration due to the power source voltage being low.
A
B
C
D
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Drive the vehicle straight ahead at 50 km/h (31 mph) or more for at least 30 seconds.
Check that the steering wheel is correctly centered while driving straight ahead.
If front wheel alignment and steering are adjusted as a result of an off-center steering wheel, acquire the yaw rate and acceleration sensor zero point again after the adjustments are completed.
The steering wheel is correctly centered.
OK
NG
Turn the engine switch off.
Replace the steering angle sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>REMOVAL).
NEXT
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Start the engine.
Drive the vehicle at a speed of 50 km/h (31 mph) or more for at least 120 seconds and turn the steering wheel to the right and left.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1439 and C1445 are not output. | A |
| Yaw rate and acceleration sensor DTCs are output. | B |
If DTC C1439 and/or C1445 is not output again, the DTC may have been stored due to a temporary loss of the steering angle zero point calibration, such as a loss of calibration due to the power source voltage being low.
A
B