Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.09–2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C146E  Open in ABS Solenoid Relay Circuit  


DESCRIPTION

The ABS solenoid relay is built into the skid control ECU in the brake actuator assembly. The ABS solenoid relay supplies power to the ABS and TRC solenoids. The skid control ECU detects a solenoid relay malfunction by performing a self check and relay operation check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C146E Open in ABS Solenoid Relay Circuit Either of the following is detected:
1.

A solenoid relay drive circuit in the skid control ECU is malfunctioning.

2.

The solenoid relay cannot be switched between on and off.


·

ABS NO. 2 fuse

·

ABS solenoid relay circuit

·

ABS solenoid relay (brake actuator assembly)



WIRING DIAGRAM

C313364E02
1.656,1.365 2.573,1.594 0.917,0.229 10 false ABS NO. 2 0.75,2.438 1.667,2.667 0.917,0.229 10 false F/B ALT 0.75,4.833 1.667,5.063 0.917,0.229 10 false FL MAIN 0.76,3.563 1.177,3.792 0.417,0.229 10 false ALT 1.729,1.052 1.969,1.281 0.24,0.229 10 false 1 2.125,1.052 2.365,1.229 0.24,0.177 10 false 2 0.844,6.833 1.375,7.063 0.531,0.229 10 false Battery 3.656,5.208 4.177,5.438 0.521,0.229 10 false GND1 3.354,4.927 3.677,5.156 0.323,0.229 10 false 38 3.667,1.333 4.083,1.563 0.417,0.229 10 false +BS 3.375,1.073 3.698,1.302 0.323,0.229 10 false 25 4.698,0.917 5.625,1.365 0.927,0.448 10 false ABS Solenoid Relay 6.083,2.177 6.542,2.406 0.458,0.229 10 false SFRH 6.083,2.688 6.542,2.917 0.458,0.229 10 false SFLH 6.083,3.198 6.542,3.427 0.458,0.229 10 false SRRH 6.083,3.667 6.542,3.896 0.458,0.229 10 false SRLH 6.083,4.156 6.542,4.385 0.458,0.229 10 false SFRR 6.083,4.656 6.542,4.885 0.458,0.229 10 false SFLR 6.073,5.156 6.531,5.385 0.458,0.229 10 false SRRR 6.083,5.646 6.542,5.875 0.458,0.229 10 false SRLR 6.083,6.135 6.542,6.365 0.458,0.229 10 false SRM1 6.083,6.635 6.542,6.865 0.458,0.229 10 false SRM2 6.083,7.146 6.542,7.375 0.458,0.229 10 false SRC1 6.083,7.635 6.542,7.865 0.458,0.229 10 false SRC2 4.573,3.26 5.729,3.469 1.156,0.208 10 false Skid Control ECU 4.802,8.302 6.531,8.51 1.729,0.208 10 false Brake Actuator Assembly 4.469,8.313 4.854,8.542 0.385,0.229 10 false A35

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

When C1241 and/or C1417 is output together with C146E, inspect and repair the trouble areas indicated by C1241 and/or C1417 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1241 for C1241 and/or Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1417 for C1417).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)
a.
U189567E02
0.719,1.5 1.125,0.844 false 0.167,0.198 0.365,0.354 0.198,0.156 10 false *a 0.24,0.781 0.531,0.938 0.292,0.156 10 false A35 1.125,0.646 1.552,0.802 0.427,0.156 10 false +BS

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-25 (+BS) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
U189568E02
2.74,1.5 2.313,0.75 false 0.188,0.198 0.385,0.354 0.198,0.156 10 false *a 0.25,0.792 0.542,0.948 0.292,0.156 10 false A35 1.99,0.531 2.417,0.688 0.427,0.156 10 false GND1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-38 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

3.RECONFIRM DTC
HINT:
·

This DTC is stored when a problem is identified in the skid control ECU (brake actuator assembly).

·

The solenoid circuits are located in the skid control ECU (brake actuator assembly).

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed.

Be sure to check if the DTC is output again before replacing the skid control ECU (brake actuator assembly).



a.

Reconnect the A35 skid control ECU (brake actuator assembly) connector.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C146E is not output. A
DTC C146E is output. B


HINT:
·

If a speed signal of 20 km/h (12 mph) or more is received by the skid control ECU (brake actuator assembly) with the engine switch on (IG), the skid control ECU (brake actuator assembly) performs self diagnosis of the motor circuit.

·

If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harnesses, and fuses of the skid control ECU (brake actuator assembly).

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.





A

B