When the A/C amplifier is turned on, a magnetic clutch ON signal is sent from the MGC terminal of the A/C amplifier. Then, the MGC relay turns on to operate the magnetic clutch.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch on.
Turn the A/C switch on and off.
Select the item below in the Data List, and read the display on the intelligent tester.
| Tester Display | Measure Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| A/C Signal
(A/C Signal) |
A/C signal / ON or OFF | ON: A/C ON
OFF: A/C OFF |
- |
The display is as specified in the normal condition column.
OK
NG
Remove the RH ECU-IG fuse from the instrument panel junction block RH.
Measure the resistance of the fuse.
| Tester Item | Condition | Specified Condition |
|---|---|---|
| RH ECU-IG | Always | Below 1 Ω |
Reconnect the RH ECU-IG fuse to the instrument panel junction block RH.
OK
NG
Remove the MG CLT relay from the engine room No. 2 relay block and junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
|---|---|
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω
(when battery voltage is applied to terminals 1 and 2) |
Install the MG CLT relay to the engine room No. 2 relay block and junction block.
OK
NG
Disconnect the connector from the A/C amplifier.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G47-20 (MGC) - Body ground | Ignition switch off | Below 1 V |
| G47-20 (MGC) - Body ground | Ignition switch on (IG) | 10 to 14 V |
OK
NG
Reconnect the connector to the A/C amplifier.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G47-20 (MGC) - Body ground | Ignition switch on (IG)
A/C switch: OFF |
10 to 14 V |
| G47-20 (MGC) - Body ground | Ignition switch on (IG)
A/C switch: ON |
Below 1 V |
OK
NG
Disconnect the connector from the A/C compressor.
Disconnect the connector from the magnetic clutch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D49-3 (MG+) - A-1 | Always | Below 1 Ω |
| D49-3 (MG+) - Body ground | Always | 10 kΩ or higher |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 - Body ground | 20°C (68°F) | 3.8 to 4.2 Ω |
When connector terminal A-1 is connected to the positive (+) battery terminal, check that the following occurs: 1) the magnetic clutch's operating sound can be heard, and 2) the magnetic clutch's hub and rotor lock.
OK
NG
Remove the MG CLT relay from the engine room No. 2 relay block and junction block.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
|---|---|
| Relay block MG CLT relay terminal 5 - Body ground | 10 to 14 V |
| Relay block MG CLT relay terminal 1 - Body ground | 10 to 14 V |
OK
NG