Home › Vehicle Interior › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM
RM24M0E _58 Vehicle Interior _059586 ENGINE IMMOBILISER _0292196 ENGINE IMMOBILISER SYSTEM U

ENGINE IMMOBILISER  ENGINE IMMOBILISER SYSTEM  TERMINALS OF ECU  


CHECK ENGINE SWITCH


U185934E03
3.458,0.188 3.781,0.365 0.323,0.177 10 false G31

a.

Disconnect the G31 switch connector.


b.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
GND (G31-5) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the G31 switch connector.


d.

Measure the resistance and voltage of the connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
AGND (G31-8) - Body ground G - Body ground Ground Always Below 1 Ω
VC5 (G31-14) - AGND (G31-8) L - G Power supply Engine immobiliser system is set
(key is not in cabin)
Below 1 V
Press engine switch* 4.6 to 5.4 V
CODE (G31-10) - AGND (G31-8) GR - G Demodulated signal of key code data Engine immobiliser system is set (key is not in cabin) Below 1 V
Engine switch pressed and key held close to engine switch* Pulse generation
(see waveform 1)
TXCT (G31-9) - AGND (G31-8) LG - G Key code output signal Engine immobiliser system is set (key is not in cabin) Below 1 V
Engine switch pressed and key held close to engine switch* Pulse generation
(see waveform 2)

HINT:

*: Remove the key's battery before performing this inspection.


If the result is not as specified, the switch may have a malfunction.



e.
B130917E05
0.115,0.104 1.052,0.302 0.938,0.198 10 false Waveform 1: 2.854,1.406 3.24,1.604 0.385,0.198 10 false GND

Using an oscilloscope, check the waveform 1.

Waveform 1 (Reference):
Item Content
Symbols (Terminal No.) CODE (G31-10) - AGND (G31-8)
Tool Setting 2 V/DIV., 20 msec./DIV.
Condition Engine switch pressed and key held close to engine switch*

HINT:

*: Remove the key's battery before performing this inspection.



f.
B130918E04
0.115,0.042 1.01,0.24 0.896,0.198 10 false Waveform 2: 2.854,1.385 3.24,1.583 0.385,0.198 10 false GND

Using an oscilloscope, check the waveform 2.

Waveform 2 (Reference):
Item Content
Symbols (Terminal No.) TXCT (G31-9) - AGND (G31-8)
Tool Setting 2 V/DIV., 20 msec./DIV.
Condition Engine switch pressed and key held close to engine switch*

HINT:

*: Remove the key's battery before performing this inspection.




CHECK CERTIFICATION ECU


U185927E03
3.479,0.313 3.823,0.49 0.344,0.177 10 false G29

a.

Disconnect the G29 ECU connector.


b.

Measure the resistance and voltage of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
E (G29-17) - Body ground W-B - Body ground Ground Always Below 1 Ω
+B (G29-1) - E (G29-17) BE - W-B +B power supply Always 9 to 14 V
IG (G29-18) - E (G29-17) B - W-B Engine power supply Ignition switch off Below 1 V

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the G29 connector.


d.

Measure the resistance and voltage of the connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
AGND (G29-40) - Body ground G - Body ground Engine switch ground Always Below 1 Ω
VC5 (G29-30) - AGND (G29-40) L - G Engine switch power supply Engine immobiliser system is set (key is not in cabin) Below 1 V
Engine switch pressed* 4.6 to 5.4 V
CODE (G29-9) - AGND (G29-40) GR - G Engine switch code input Engine immobiliser system is set (key is not in cabin) Below 1 V
Engine switch pressed and key held close to engine switch* Pulse generation
(see waveform 1)
TXCT (G29-8) - AGND (G29-40) LG - G Engine switch TX output Engine immobiliser system is set (key is not in cabin) Below 1 V
Engine switch pressed and key held close to engine switch* Pulse generation
(see waveform 2)

HINT:

*: Remove the key's battery before performing this inspection.


If the result is not as specified, the ECU may have a malfunction.



e.
B130917E05
0.115,0.104 1.052,0.302 0.938,0.198 10 false Waveform 1: 2.854,1.406 3.24,1.604 0.385,0.198 10 false GND

Using an oscilloscope, check the waveform 1.

Waveform 1 (Reference):
Item Content
Symbols (Terminal No.) CODE (G29-9) - AGND (G29-40)
Tool Setting 2 V/DIV., 20 msec./DIV.
Condition Engine switch pressed and key held close to engine switch*

HINT:

*: Remove the key's battery before performing this inspection.



f.
B130918E04
0.115,0.042 1.01,0.24 0.896,0.198 10 false Waveform 2: 2.854,1.385 3.24,1.583 0.385,0.198 10 false GND

Using an oscilloscope, check the waveform 2.

Waveform 2 (Reference):
Item Content
Symbols (Terminal No.) TXCT (G29-8) - AGND (G29-40)
Tool Setting 2 V/DIV., 20 msec./DIV.
Condition Engine switch pressed and key held close to engine switch*

HINT:

*: Remove the key's battery before performing this inspection.




CHECK ID CODE BOX


U185928E03
3.479,0.635 3.781,0.813 0.302,0.177 10 false G20

a.

Disconnect the G20 box connector.


b.

Measure the resistance and voltage of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
GND (G20-8) - Body ground W-B - Body ground Ground Always Below 1 Ω
+B (G20-1) - GND (G20-8) BE - W-B +B power supply Always 9 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the G20 box connector.


d.

Measure the voltage of the connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
EFII (G20-5) - GND (G20-8) G - W-B ECM input signal Ignition switch off Below 1 V
Ignition switch on (IG) Pulse generation (see waveform 1)
EFIO (G20-6) - GND (G20-8) R - W-B ECM output signal Ignition switch off Below 1 V
Ignition switch on (IG) Pulse generation (see waveform 2)

If the result is not as specified, the box may have a malfunction.



e.
B130919E07
0.146,0.167 1.073,0.365 0.927,0.198 10 false Waveform 1: 2.844,1.167 3.229,1.365 0.385,0.198 10 false GND

Using an oscilloscope, check the waveform 1.

Waveform 1 (Reference):
Item Content
Symbols (Terminal No.) EFII (G20-5) - GND (G20-8)
Tool Setting 10 V/DIV., 100 msec./DIV.
Condition Ignition switch on (IG)


f.
B130920E07
0.125,0.188 0.99,0.385 0.865,0.198 10 false Waveform 2: 2.813,1.188 3.198,1.385 0.385,0.198 10 false GND

Using an oscilloscope, check the waveform 2.

Waveform 2 (Reference):
Item Content
Symbols (Terminal No.) EFIO (G20-6) - GND (G20-8)
Tool Setting 10 V/DIV., 100 msec./DIV.
Condition Ignition switch on (IG)



CHECK STEERING LOCK ACTUATOR (STEERING LOCK ECU)


U185922E03
3.438,0.271 3.75,0.469 0.313,0.198 10 false G32

a.

Disconnect the G32 ECU connector.


b.

Measure the resistance and voltage of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
SGND (G32-2) - Body ground W-B - Body ground Ground Always Below 1 Ω
GND (G32-1) - Body ground W-B - Body ground Ground Always Below 1 Ω
B (G32-7) - Body ground B - Body ground +B power supply Always 9 to 14 V
IG2 (G32-6) - Body ground B - Body ground Engine power supply Ignition switch off Below 1 V
Ignition switch on (IG) 9 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.




CHECK ECM


U188585E02
5.594,0.646 5.844,0.844 0.25,0.198 10 false A7 2.208,0.656 2.469,0.833 0.26,0.177 10 false D1 2.594,0.625 2.844,0.792 0.25,0.167 10 false (*1) 0.469,0.24 1.417,0.385 0.948,0.146 10 false *1: for 2GR-FE 3.135,0.646 3.396,0.823 0.26,0.177 10 false D2 3.542,0.646 3.792,0.813 0.25,0.167 10 false (*2) 0.469,0.5 1.417,0.646 0.948,0.146 10 false *2: for 2AZ-FE

a.

Measure the resistance and voltage of the wire harness side connector.

2AZ-FE:
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
E1 (D2-104) - Body ground BR - Body ground Ground Always Below 1 Ω
IMI (A7-11) - E1 (D2-104) R - BR Transponder key ECU input signal Ignition switch off Below 1 V
Ignition switch on (IG) Pulse generation (see waveform 1)
IMO (A7-10) - E1 (D2-104) BE - BR Transponder key ECU output signal Ignition switch off Below 1 V
Ignition switch on (IG) Pulse generation (see waveform 2)

2GR-FE:
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
E1 (D1-81) - Body ground BR - Body ground Ground Always Below 1 Ω
IMI (A7-11) - E1 (D1-81) R - BR Transponder key ECU input signal Ignition switch off Below 1 V
Ignition switch on (IG) Pulse generation (see waveform 1)
IMO (A7-10) - E1 (D1-81) BE - BR Transponder key ECU output signal Ignition switch off Below 1 V
Ignition switch on (IG) Pulse generation (see waveform 2)

If the result is not as specified, there may be a malfunction in the wire harness.


b.
B130920E08
0.146,0.135 1.01,0.333 0.865,0.198 10 false Waveform 1: 2.854,1.156 3.24,1.354 0.385,0.198 10 false GND

Using an oscilloscope, check the waveform 1.

Waveform 1 (Reference):
Item Content
Symbols (Terminal No.) IMI (A7-11) - E1 (D2-104)
IMI (A7-11) - E1 (D1-81)
Tool Setting 10 V/DIV., 500 msec./DIV.
Condition Ignition switch on (IG)


c.
B130919E08
0.115,0.115 1.042,0.313 0.927,0.198 10 false Waveform 2: 2.833,1.177 3.219,1.375 0.385,0.198 10 false GND

Using an oscilloscope, check the waveform 2.

Waveform 2 (Reference):
Item Content
Symbols (Terminal No.) IMO (A7-10) - E1 (D2-104)
IMO (A7-10) - E1 (D1-81)
Tool Setting 10 V/DIV., 500 msec./DIV.
Condition Ignition switch on (IG)



CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK LH)


U185960E03
0.125,0.125 1.74,0.302 1.615,0.177 10 false Vehicle Front Side: 5.542,0.125 6.938,0.302 1.396,0.177 10 false Vehicle Rear Side: 1.323,1.594 1.51,1.771 0.188,0.177 10 false 4A 1.594,4.656 1.781,4.833 0.188,0.177 10 false 4A 1.323,2.813 1.521,2.99 0.198,0.177 10 false 4D 5.594,4.635 5.792,4.813 0.198,0.177 10 false 4D 5.698,2.448 5.885,2.625 0.188,0.177 10 false 4K 3.177,6.021 3.365,6.198 0.188,0.177 10 false 4K 5.677,1.573 5.875,1.75 0.198,0.177 10 false 4G 5.552,5.99 5.75,6.167 0.198,0.177 10 false 4G 5.708,2.896 5.875,3.073 0.167,0.177 10 false 4L 1.844,6.083 2.01,6.26 0.167,0.177 10 false 4L 6.083,1.573 6.365,1.75 0.281,0.177 10 false G57 5.583,7.333 5.865,7.51 0.281,0.177 10 false G57 6.073,2.083 6.354,2.26 0.281,0.177 10 false G58 4.396,7.333 4.677,7.51 0.281,0.177 10 false G58 6.073,2.51 6.354,2.688 0.281,0.177 10 false G59 3.385,7.333 3.667,7.51 0.281,0.177 10 false G59 6.073,2.813 6.354,2.99 0.281,0.177 10 false G60 2.771,7.333 3.052,7.51 0.281,0.177 10 false G60 5.688,3.208 5.896,3.385 0.208,0.177 10 false 4M 0.667,6.083 0.875,6.26 0.208,0.177 10 false 4M 6.146,3.198 6.344,3.375 0.198,0.177 10 false 4N 1.177,7.521 1.375,7.698 0.198,0.177 10 false 4N

a.

Disconnect the 4A, G57, G58 and G59 ECU connectors.


b.

Measure the resistance and voltage of the wire harness side connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
GND1 (G59-1) - Body ground W-B - Body ground Ground Always Below 1 Ω
GND2 (4A-3) - Body ground W-B - Body ground Ground Always Below 1 Ω
AM1 (G57-6) - Body ground SB -Body ground +B power supply Always 9 to 14 V
AM2 (G58-1) - Body ground SB -Body ground +B power supply Always 9 to 14 V
SSW1 (G57-17) - Body ground P -Body ground Engine switch Ignition switch off 10 kΩ or higher
Ignition switch on (IG) Below 1 Ω
SSW2 (G57-16) - Body ground G -Body ground Engine switch Ignition switch off 10 kΩ or higher
Ignition switch on (IG) Below 1 Ω
LIN1 (4A-20) - Body ground R - Body ground LIN communication line Always 10 kΩ or higher

If the result is not as specified, there may be a malfunction on the wire harness side.