Home › Vehicle Interior › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM
RM24M0E _58 Vehicle Interior _059586 ENGINE IMMOBILISER _0292196 ENGINE IMMOBILISER SYSTEM D

ENGINE IMMOBILISER  ENGINE IMMOBILISER SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


a.

Engine immobiliser system data and Diagnostic Trouble Codes (DTCs) can be read through the vehicle's Data Link Connector 3 (DLC3). In some cases, a malfunction may be occurring in the immobiliser system even though the security indicator light is not illuminated. When the system seems to be malfunctioning, use the intelligent tester to check for malfunctions and perform repairs.



CHECK DLC3


H103023E07
1.708,1.875 1.948,1.469 true 1.563,0.917 1.208,0.438 true 1.76,0.927 1.542,0.448 true 1.948,0.927 2.031,0.448 true 2.135,0.927 2.427,0.458 true 2.458,1.896 2.313,1.479 true 1.031,0.25 1.281,0.427 0.25,0.177 10 false CG 1.427,1.906 1.896,2.094 0.469,0.188 10 false CANL 1.396,0.25 1.646,0.427 0.25,0.177 10 false SG 1.813,0.229 2.271,0.396 0.458,0.167 10 false CANH 2.417,0.229 2.677,0.406 0.26,0.177 10 false SIL 2.333,1.917 2.802,2.104 0.469,0.188 10 false BAT

The vehicle's ECU uses the ISO 15765-4 communication protocol. The terminal arrangement of the DLC3 complies with SAE J1962 and matches the ISO 15765-4 format.

Symbols (Terminal No.) Terminal Description Condition Specified Condition
SIL (7) - SG (5) Bus "+" line During transmission Pulse generation
CG (4) - Body ground Chassis ground Always Below 1 Ω
SG (5) - Body ground Signal ground Always Below 1 Ω
BAT (16) - Body ground Battery positive Always 11 to 14 V
CANH (6) - CANL (14) CAN bus line Ignition switch off* 54 to 69 Ω
CANH (6) - BAT(16) HIGH-level CAN bus line Ignition switch off* 6 kΩ or higher
CANH (6) - CG (4) HIGH-level CAN bus line Ignition switch off* 200 Ω or higher
CANL (14) - BAT(16) LOW-level CAN bus line Ignition switch off* 6 kΩ or higher
CANL (14) - CG (4) LOW-level CAN bus line Ignition switch off* 200 Ω or higher

NOTICE:

*: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.


If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.

HINT:
B135940E01
0.425,2.845 1.557,3.021 1.132,0.177 10 Intelligent Tester 0.6,2.589 0.6,2.832 false 1.48,2.058 1.864,2.214 0.385,0.156 10 DLC3 1.717,2.051 1.841,1.732 false

Connect the cable of the intelligent tester to the DLC3, turn the ignition switch on (IG) and attempt to use the intelligent tester. If the screen displays UNABLE TO CONNECT TO VEHICLE, a problem exists in the vehicle side or the tester side.

If the communication is normal when the tester is connected to another vehicle, inspect the DLC3 on the original vehicle.

If the communication is still not possible when the tester is connected to another vehicle, the problem is probably in the tester itself. Consult the Service Department listed in the tester's instruction manual.