Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059587 METER / GAUGE / DISPLAY _0292197 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Operating Light Control Rheostat does not Change Light Brightness  


DESCRIPTION

The combination meter sub-assembly receives signals from this circuit to adjust the illumination of the combination meter sub-assembly. The combination meter sub-assembly sets the illumination level based on the user operation of the light control rheostat switch in the trip switch.

HINT:
·

The meter illumination level can be adjusted by pressing the light control rheostat switch.

·

The meter illumination dims when the taillights come on.



WIRING DIAGRAM

E274343E12
1.458,1.073 2.042,1.229 0.583,0.156 10 false Rheostat 2.323,0.823 2.531,0.979 0.208,0.156 10 false TC 2.656,0.833 2.865,0.99 0.208,0.156 10 false 4 2.417,2.25 2.531,2.406 0.115,0.156 10 false E 2.667,2.24 2.844,2.396 0.177,0.156 10 false 6 5.427,0.813 5.604,0.969 0.177,0.156 10 false 35 5.698,0.927 6.052,1.083 0.354,0.156 10 false TC O 5.448,2.885 5.74,3.042 0.292,0.156 10 false G28 5.448,3.042 6.719,3.531 1.271,0.49 10 false Combination Meter Sub-assembly 1.417,2.927 1.708,3.083 0.292,0.156 10 false G46 1.417,3.104 2.125,3.26 0.708,0.156 10 false Trip Switch

PROCEDURE

1.READ VALUE USING GTS (LIGHT CONTROL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Light Control Switch Light control rheostat switch / ON or OFF ON: Switch pushed
OFF: Switch released
-

OK:

Light control rheostat switch condition displayed on the GTS changes with the actual switch operation.




OK

REPLACE COMBINATION METER SUB-ASSEMBLY

NG

2.INSPECT TRIP SWITCH
2.INSPECT TRIP SWITCH
a.
E127509E26
2.104,1.542 2.646,1.542 false 1.552,1.271 1.552,0.688 false 1.49,0.49 1.708,0.646 0.219,0.156 10 false TC 2.708,1.448 2.823,1.604 0.115,0.156 10 false E 0.073,0.042 0.24,0.198 0.167,0.156 10 false *a

Remove the trip switch (see page Vehicle Interior>LIGHTING>HAZARD WARNING SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (TC) - 6 (E) Light control rheostat switch is pressed Below 1 Ω
Light control rheostat switch is not pressed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Trip Switch)



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - TRIP SWITCH)

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - TRIP SWITCH)
a.

Disconnect the G28 combination meter sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G28-35 (TC O) - G46-4 (TC) Always Below 1 Ω
G28-35 (TC O) or G46-4 (TC) - Body ground Always 10 kΩ or higher
G46-6 (E) - Body ground Always Below 1 Ω




OK

REPLACE COMBINATION METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR