Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2013.04–2014.09
RM24M0E _56 Audio / Visual / Telematics _059588 NAVIGATION / MULTI INFO DISPLAY _0292199 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15C2  Speed Signal Malfunction  


DESCRIPTION

The navigation receiver assembly receives a vehicle speed signal from the combination meter assembly and information from the navigation antenna assembly, and then adjusts the vehicle position.

The navigation receiver assembly stores this DTC when the difference between the speed information that the navigation antenna assembly receives and the SPD pulse received from the combination meter assembly becomes large.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



DTC No. DTC Detection Condition Trouble Area
B15C2 A difference between the GPS speed and SPD pulse is detected.
·

Navigation receiver assembly

·

Combination meter assembly

·

Harness or connector



WIRING DIAGRAM

E226158E74
1.451,1.077 1.690,1.240 0.239,0.163 10 +S 5.521,1.077 5.892,1.240 0.371,0.163 10 SPD 1.71,0.948 1.907,1.086 0.198,0.139 10 40 5.275,0.948 5.452,1.086 0.177,0.139 10 17 0.624,1.939 0.919,2.095 0.295,0.156 10 G28 0.624,2.086 1.863,2.423 1.239,0.336 10 Combination Meter Assembly 5.24,1.915 5.556,2.099 0.316,0.184 10 F17 5.24,2.066 6.580,2.453 1.340,0.387 10 Navigation Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the navigation receiver assembly, perform vehicle contract setting (See page Audio / Visual / Telematics>G-BOOK>G-BOOK SYSTEM>REGISTRATION).


PROCEDURE

1.CHECK VEHICLE SENSOR (OPERATION CHECK)
a.
E176549

Enter the "Vehicle Sensors" screen. Refer to Check GPS & Vehicle Sensors in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).


b.

While driving the vehicle, compare the "Speed" indicator to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "Vehicle Sensors" screen is almost the same as the actual vehicle speed measured using the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).




OK

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F17 navigation receiver assembly connector.


b.

Disconnect the G28 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F17-17 (SPD) - G28-40 (+S) Always Below 1 Ω




OK

3.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR)

3.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
U189937E01
1.582,0.672 1.924,0.828 0.342,0.156 10 F17 0.181,0.157 0.336,0.312 0.154,0.156 10 *a 0.813,2.735 1.177,2.890 0.364,0.156 10 SPD 1.19,2.222 1.01,2.72 false

Reconnect the combination meter assembly.

i.

Check the output waveform.


ii.

Connect an oscilloscope to terminal F17-17 (SPD) and body ground.


iii.

Turn the engine switch on (IG).


iv.

Turn a wheel slowly.


v.
E359820E01
2.844,1.26 3.26,1.469 0.417,0.208 10 false GND 0.948,1.615 1.365,1.823 0.417,0.208 10 false (A)

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F17-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.





OK

NG

REPLACE COMBINATION METER ASSEMBLY