Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM24M0E _56 Audio / Visual / Telematics _059590 PARK ASSIST / MONITORING _0292203 PARKING ASSIST MONITOR SYSTEM J

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  Guide Lines and Buttons are not Displayed for All Display Modes  


DESCRIPTION

The navigation receiver assembly receives back door open/close signals from the main body ECU (instrument panel junction block assembly) via CAN communication. When the back door is open, the camera aiming cannot be adjusted correctly because the rear television camera assembly is installed on the back door. Therefore, when adjusting the camera aiming calibration while the back door is open, a back door open warning message will be displayed on the screen and camera aiming adjustment will be canceled.

HINT:
·

Check the parking assist monitor screen display mode settings. (Check if the parking guide lines are set to off.)

·

The back door lock assembly is connected to the main body ECU (instrument panel junction block assembly)*1 or power back door ECU (back door motor unit)*2 by the vehicle wire harness.


*1: w/o Power Back Door System

*2: w/ Power Back Door System



WIRING DIAGRAM

E249339E04
5.717,2.785 7.021,3.144 1.304,0.360 10 Navigation Receiver Assembly 3.083,2.794 5.286,3.172 2.202,0.378 10 Main Body ECU (Instrument Panel Junction Block Assembly) 3.083,2.654 3.397,2.805 0.313,0.151 10 G58 3.714,2.297 4.166,2.448 0.452,0.151 10 BCTY 3.469,2.212 3.678,2.364 0.209,0.151 10 25 3.224,1.185 5.176,1.563 1.952,0.378 10 Power Back Door ECU (Back Door Motor Unit)*1 3.224,1.045 3.537,1.196 0.313,0.151 10 M24 3.7,0.702 4.020,0.853 0.320,0.151 10 FUL 3.455,0.59 3.664,0.741 0.209,0.151 10 20 1.017,2.392 1.375,2.544 0.358,0.151 10 ACT- 1.858,2.392 2.076,2.544 0.219,0.151 10 D+ 0.835,2.212 0.954,2.364 0.119,0.151 10 1 2.117,2.212 2.236,2.364 0.119,0.151 10 3 0.8,2.738 2.599,2.935 1.799,0.198 10 Back Door Lock Assembly*2 0.8,2.598 1.083,2.749 0.283,0.151 10 S11 0.991,0.777 1.103,0.928 0.112,0.151 10 E 1.75,0.777 2.046,0.928 0.295,0.151 10 CTY 0.821,0.583 0.940,0.734 0.119,0.151 10 4 2.103,0.583 2.222,0.734 0.119,0.151 10 3 0.786,1.136 2.599,1.334 1.813,0.198 10 Back Door Lock Assembly*1 0.786,0.996 1.071,1.147 0.286,0.151 10 S12 4.089,4.1 6.166,4.387 2.077,0.287 10 *2: w/o Power Back Door System 4.089,3.757 6.099,4.044 2.010,0.287 10 *1: w/ Power Back Door System 0.815,4.288 2.554,4.462 1.739,0.173 10 : CAN Communication Line 5.29,1.451 5.471,1.602 0.181,0.151 10 *1

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the navigation receiver assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION).



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turning the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body*1 or Back Door*2 / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body*1
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Back Door Courtesy SW Back door courtesy light switch signal/ ON or OFF ON: Back door open
OFF: Back door closed
-

Back Door*2
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Courtesy SW Back door courtesy light switch signal/ ON or OFF ON: Back door open
OFF: Back door closed
-

*1: w/o Power Back Door System

*2: w/ Power Back Door System


OK:

The back door courtesy light switch functions as specified in the normal condition column.


Result:
Result Proceed to
OK A
NG (w/o Power Back Door System) B
NG (w/ Power Back Door System) C




A

B

2.INSPECT BACK DOOR LOCK ASSEMBLY

C

4.INSPECT BACK DOOR LOCK ASSEMBLY
2.INSPECT BACK DOOR LOCK ASSEMBLY
a.

Remove the back door lock assembly.


b.

Inspect the back door courtesy light switch built into the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MAIN BODY ECU)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MAIN BODY ECU)
a.

Disconnect the G58 main body ECU (instrument panel junction block assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S11-3 (D+) - G58-25 (BCTY) Always Below 1 Ω
S11-3 (D+) - Body ground Always 10 kΩ or higher
S11-1 (ACT-) - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BACK DOOR LOCK ASSEMBLY
a.

Remove the back door lock assembly.


b.

Inspect the back door courtesy light switch built into the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - POWER BACK DOOR ECU)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - POWER BACK DOOR ECU)
a.

Disconnect the M24 power back door ECU (back door motor unit) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S12-3 (CTY) - M24-20 (FUL) Always Below 1 Ω
S12-3 (CTY) - Body ground Always 10 kΩ or higher
S12-4 (E) - Body ground Always Below 1 Ω




OK

REPLACE POWER BACK DOOR ECU (BACK DOOR MOTOR UNIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR