GENERAL
When the vehicle is driven at 10 km/h (6 mph) or less, the ultrasonic sensors detect any obstacles at the corners and rear of the vehicle. The system then informs the driver of the distance between the sensors and the obstacles as well as their positions by indicating them on the clearance warning indicator and by sounding a buzzer.
FUNCTION OF COMPONENTS
| Components | Function |
|---|---|
| Ultrasonic sensor | ultrasonic sensor consists of a sensor portion that transmits and receives ultrasonic waves and a pre-amplifier that amplifies the waves. The ultrasonic sensor outputs the ultrasonic transmission and reception signals to the clearance warning ECU assembly. |
| Clearance warning indicator assembly
(clearance sonar main switch) |
Displays the location of the obstacle and the approximate distance between the vehicle and the obstacle. Turns the clearance sonar system on and off. |
| Buzzer in the clearance warning indicator assembly | Emits an intermittent sound to inform the driver that the ECU has detected an obstacle within prescribed ranges. |
| Clearance warning ECU assembly | Judges the approximate distance between the vehicle and the obstacle based on the signals from the ultrasonic sensors and sends the display signal to the clearance warning indicator and the buzzer signal to the buzzer. |
| Park/neutral position switch assembly | Sends a signal that activates the clearance sonar system when the shift lever is moved to the P or R position. |
OPERATION EXPLANATION
The clearance warning ECU assembly determines whether the clearance sonar system should be operated based on the clearance sonar main switch on/off status, the shift position and the vehicle speed.
When the system operates, the clearance warning ECU assembly transmits ultrasonic waves from the ultrasonic sensors. If these waves encounter an obstacle within one or more of the sensors' ranges, the waves are reflected back to the sensors, which transmit them to the clearance warning ECU assembly. Based on this information, the clearance warning ECU assembly sends signals to the clearance warning indicator and the buzzer. The approximate distance between the vehicle and the obstacle is then indicated, and the buzzer sounds.
Refer to Operation Check for the detailed operation (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM(for LHD)>OPERATION CHECK).
COMMUNICATION SIGNALS OF COMPONENTS
Allocation refers to the process of the clearance warning ECU assembly setting aside IDs for the sensors.
The vehicle has the sensors arranged in 2 groups. There is a front series and a rear series. The sensors are connected in a "daisy chain".
Initialization mode:
An ID is allocated to each sensor and sensor diagnosis is performed.
When the initial check is operating (the engine switch is on (IG) and the back sonar or clearance sonar switch assembly is on), the clearance warning ECU assembly provides power to the first sensors in each series (front corner ultrasonic sensor (LH) and rear corner ultrasonic sensor (RH)).
After the power is supplied, the front corner ultrasonic sensor (LH) and rear corner ultrasonic sensor (RH) enter standby mode to receive an ID from the clearance warning ECU assembly. When a certain amount of time has elapsed, the clearance warning ECU assembly sends an ID allocation signal to these sensors.
The front corner ultrasonic sensor (LH) and rear corner ultrasonic sensor (RH) receive the ID allocation signal from the clearance warning ECU assembly and perform self-diagnosis. When the sensor self-diagnosis is completed, the clearance warning ECU assembly sends an ID allocation confirmation signal to these sensors.
After the ID allocation confirmation is performed, the clearance warning ECU assembly provides power to the second sensors in each series (front corner ultrasonic sensor (RH) and rear center ultrasonic sensor (RH)) via the first sensors. In the same manner as the first sensors, the second sensors enter standby mode. When a certain amount of time has elapsed, the clearance warning ECU assembly sends an ID allocation signal to the second sensors.
The above operation will be repeated until an ID is allocated to the last sensor, which is in the rear series (rear corner ultrasonic sensor (LH)). Initialization ends when ID allocation to all ultrasonic sensors is completed.
Detection mode:
After initialization mode is completed, the system switches into detection mode. In detection mode, the clearance warning ECU assembly sends information request signals and sensor activation signals to the ultrasonic sensors and receives detection result signals from the sensors.
The clearance warning ECU assembly regularly sends ID signals, information request signals, and sensor activation signals to each ultrasonic sensor according to the communication schedule.
When a certain amount of time has elapsed (sensor detection operation is completed), the clearance warning ECU assembly sends an ID signal to the sensor to receive a detection result signal.
The ultrasonic sensor sends a detection result signal or detection information signal to the clearance warning ECU assembly.
The above operation is performed repeatedly for each ultrasonic sensor.