Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for RHD) › from 2016.05
RM24M0E _56 Audio / Visual / Telematics _059590 PARK ASSIST / MONITORING _0292210 TOYOTA PARKING ASSIST-SENSOR SYSTEM(for RHD) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(for RHD)  Clearance Warning Buzzer Circuit  


DESCRIPTION

This circuit consists of the No. 1 clearance warning buzzer and clearance warning ECU assembly. An ECU-excited type buzzer is used. The clearance warning ECU assembly operates the buzzer using a sound pattern that changes depending on the distance to the obstacle.

WIRING DIAGRAM

E220929E47
1.979,1.333 2.073,1.49 0.094,0.156 10 false 1 3.271,1.333 3.365,1.49 0.094,0.156 10 false 2 1.635,1.969 2.083,2.135 0.448,0.167 10 false G124 1.625,2.135 3.719,2.344 2.094,0.208 10 false No. 1 Clearance Warning Buzzer 4.219,1.948 4.656,2.125 0.438,0.177 10 false G111 4.198,2.104 6.375,2.344 2.177,0.24 10 false Clearance Warning ECU Assembly 4.688,0.583 4.896,0.781 0.208,0.198 10 false 14 4.948,0.708 5.313,0.906 0.365,0.198 10 false CBZ 4.677,1.323 4.896,1.51 0.219,0.188 10 false 13 4.948,1.427 5.24,1.646 0.292,0.219 10 false EF 2.146,1.333 2.344,1.49 0.198,0.156 10 false Z+ 3.052,1.333 3.219,1.49 0.167,0.156 10 false Z-

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Sonar / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Clearance Sonar
Tester Display Test Part Control Range Diagnostic Note
Buzzer No. 1 clearance warning buzzer Operate or Stop Confirm that the vehicle is stopped and the engine switch is on (IG)

OK:

The No. 1 clearance warning buzzer sounds.




OK

NG

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
a.

Disconnect the G124 No. 1 clearance warning buzzer connector.


b.

Disconnect the G111 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G111-14 (CBZ) - G124-1 Always Below 1 Ω
G111-13 (EF) - G124-2 Always Below 1 Ω
G111-14 (CBZ) - Body ground Always 10 kΩ or higher
G111-13 (EF) - Body ground Always 10 kΩ or higher




OK

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER
a.

Replace the No. 1 clearance warning buzzer with a new or known good one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING BUZZER>REMOVAL).



NEXT

4.PERFORM ACTIVE TEST USING GTS
4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Sonar / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Clearance Sonar
Tester Display Test Part Control Range Diagnostic Note
Buzzer No. 1 clearance warning buzzer Operate or Stop Confirm that the vehicle is stopped and the engine switch is on (IG)

OK:

The No. 1 clearance warning buzzer sounds.




OK

END (NO. 1 CLEARANCE WARNING BUZZER WAS DEFECTIVE)

NG