Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059592 WINDOW / GLASS _0292216 POWER WINDOW CONTROL SYSTEM D

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  OPERATION CHECK  


CHECK WINDOW LOCK SWITCH


B140183

a.

Check that the passenger side power window and rear windows cannot be operated when the window lock switch of the multiplex network master switch is pressed.

OK:

Operation of passenger side power window and rear window are disabled.



b.

Check that the passenger side power window and rear windows can be operated when the window lock switch is pressed again.

OK:

Passenger side power window and rear windows can be operated.




CHECK MANUAL UP / DOWN FUNCTION


a.

Check that the driver side power window operates as follows:

OK
Condition Master Switch Switch Operation Power Window
Engine switch on (IG) Driver side Pulled halfway up UP (Closes)
Pushed halfway down DOWN (Opens)


b.

Check that the passenger side and rear power windows operate as follows:

OK
Condition Regulator Switch Switch Operation Power Window
·

Engine switch on (IG)

·

Window lock switch off


Passenger side Pulled halfway up UP (Closes)
Pushed halfway down DOWN (Opens)
Rear LH side Pulled halfway up UP (Closes)
Pushed halfway down DOWN (Opens)
Rear RH side Pulled halfway up UP (Closes)
Pushed halfway down DOWN (Opens)



CHECK AUTO UP / DOWN FUNCTION


a.

Check that the driver side power window operates as follows:

OK
Condition Master Switch Switch Operation Power Window
Engine switch on (IG) Driver side Pulled up (One touch operation) AUTO UP (Closes)
Pushed down (One touch operation) AUTO DOWN (Opens)


b.

Check that the passenger side and rear power windows operate as follows:

OK
Condition Regulator Switch Switch Operation Power Window
·

Engine switch on (IG)

·

Window lock switch off


Passenger side Pulled up (One touch operation) AUTO UP (Closes)
Pushed down (One touch operation) AUTO DOWN (Opens)
Rear LH side Pulled up (One touch operation) AUTO UP (Closes)
Pushed down (One touch operation) AUTO DOWN (Opens)
Rear RH side Pulled up (One touch operation) AUTO UP (Closes)
Pushed down (One touch operation) AUTO DOWN (Opens)



CHECK REMOTE MANUAL UP / DOWN FUNCTION


a.

Check that the passenger side and rear power windows operate as follows:

OK
Condition Master Switch Switch Operation Power Window
·

Engine switch on (IG)

·

Window lock switch off


Passenger side Pulled up UP (Closes)
Pushed down DOWN (Opens)
Rear LH side Pulled up UP (Closes)
Pushed down DOWN (Opens)
Rear RH side Pulled up UP (Closes)
Pushed down DOWN (Opens)



CHECK REMOTE AUTO UP / DOWN FUNCTION


a.

Check that the passenger side and rear power windows operate as follows:

OK
Condition Master Switch Switch Operation Power Window
·

Engine switch on (IG)

·

Window lock switch off


Passenger side Pulled up (One touch operation) AUTO UP (Closes)
Pushed down (One touch operation) AUTO DOWN (Opens)
Rear LH side Pulled up (One touch operation) AUTO UP (Closes)
Pushed down (One touch operation) AUTO DOWN (Opens)
Rear RH side Pulled up (One touch operation) AUTO UP (Closes)
Pushed down (One touch operation) AUTO DOWN (Opens)



CHECK POWER WINDOW OPERATION FUNCTION AFTER ENGINE SWITCH IS TURNED OFF


a.

Check that all the power windows can be operated with the multiplex network master switch after the engine switch is turned off.


b.

Check that the key-off operation function does not operate after the driver door or front passenger door is opened.


c.

Check that all the power windows cannot be operated after more than approximately 45 seconds have elapsed since the engine switch was turned off.



CHECK JAM PROTECTION FUNCTION


a.

Check the basic function.

CAUTION:
·

The jam protection function is operative during both the AUTO UP and MANUAL UP operation.

·

Do not put your fingers between the door frame and door glass to check functions. Also, prevent any part of your body from being caught during inspection.



HINT:

The jam protection function is operative during both the AUTO UP and MANUAL UP operation while the engine runs or the engine switch is on (IG), and also after the key is removed from the door key cylinder.


i.

Fully open the window.


ii.

Set a thick book wrapped with a shop rag or piece of cloth near the power window fully closed position.


iii.
E124619E01
1.775,1.423 1.26,0.65 1.26,0.65 1.154,0.65 false 0.243,0.551 1.035,0.762 0.792,0.211 10 Thick Book

Operate the AUTO UP or MANUAL UP function to check that the power window goes down before the book is caught between the window and door frame, and stops when the opening reaches approximately 200 mm (7.87 in.).

HINT:

The power window moves down approximately 50 mm (1.97 in.). However, when the opening does not reach 200 mm (7.87 in.), the power window continues to go down until the opening reaches 200 mm (7.87 in.) or until approximately 5 seconds have elapsed.



iv.

While the power window is moving down, check that the door glass cannot be moved up even when the power window switch is used.




CHECK WIRELESS TRANSMITTER-LINKED FUNCTION


HINT:

The default setting for the wireless transmitter-linked function is off. If necessary, the function must be set to on through the customize function (See page Vehicle Interior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>CUSTOMIZE PARAMETERS).


a.

Check that all power windows operate as follows when operating the transmitter:

OK
Condition Transmitter Operation Power Window
No key is inside vehicle, and all doors are closed and locked UNLOCK switch pressed for more than 3.0 seconds DOWN (Opens)
No key is inside vehicle, and all doors are closed and locked UNLOCK switch released STOP
No key is inside vehicle, and all doors are closed and locked LOCK switch pressed for more than 3.0 seconds UP (Closes)
No key is inside vehicle, and all doors are closed and locked LOCK switch released STOP



CHECK KEY-LINKED FUNCTION USING DRIVER DOOR KEY CYLINDER


HINT:

The default setting for the key-linked function using driver door key cylinder is off. If necessary, the function must be set to on through the customize function (See page Vehicle Interior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>CUSTOMIZE PARAMETERS).


a.

Check that all power windows operate as follows:

OK
Condition Door Key Cylinder Operation Power Window
No key is inside vehicle, and all doors are closed Held (LOCK) for more than 1.5 seconds UP (Closes)
No key is inside vehicle, and all doors are closed Returned to neutral position STOP
No key is inside vehicle, and all doors are closed Held (UNLOCK) for more than 1.5 seconds DOWN (Opens)
No key is inside vehicle, and all doors are closed Returned to neutral position STOP



CHECK ENTRY LOCK SWITCH-LINKED CLOSE FUNCTION (w/ Entry Lock Switch-linked Close Function


HINT:

The default setting for the entry lock switch-linked close function is off. If necessary, the function must be set to on through the customize function (See page Vehicle Interior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>CUSTOMIZE PARAMETERS).


a.

Check that all power windows operate as follows when the entry lock switch is pressed and held:

OK
Condition Transmitter Operation Power Window
No key is inside vehicle, and all doors are closed Entry lock switch pressed for more than 3.0 seconds UP (Closes)
No key is inside vehicle, and all doors are closed Entry lock switch released STOP



CHECK WINDOW OPEN WARNING FUNCTION (for RHD)


a.

Open a window using the power window switch.


b.

Turn the engine switch from on (IG) to off, open the driver door with the electronic key transmitter in the vehicle and check that the warning buzzer in the combination meter assembly sounds once. Then, check that "Window opened" is displayed on the multi-information display in the combination meter assembly.



CHECK POWER WINDOW SWITCH LED ILLUMINATION (for LHD)


a.

Check the LED illumination.

i.

Check that the LED located on the power window switch illuminates when the engine switch is turned on (IG) and window lock switch is set to the UNLOCK position.




CHECK POWER WINDOW SWITCH LED ILLUMINATION (for RHD)


a.

Check the LED illumination.

i.

Check that the LED located on the power window switch illuminates when the engine switch is turned on (IG).