Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM24M0E _58 Vehicle Interior _059592 WINDOW / GLASS _0292216 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2321  Driver Side Door ECU Communication Stop  


DESCRIPTION

DTC B2321 is output when communication between the power window regulator motor (for driver side) and main body ECU stops for more than 10 seconds.

DTC No. DTC Detection Condition Trouble Area
B2321 No communication between power window regulator motor (for driver side) and main body ECU for more than 10 seconds
·

Power window regulator motor (for driver side)

·

Main body ECU

·

Wire harness



WIRING DIAGRAM

B142471E05
2.058,2.826 4.123,2.989 2.065,0.164 10 Multiplex Network Master Switch 3.674,0.512 4.463,0.675 0.790,0.164 10 from Battery 5.902,0.506 6.362,0.670 0.460,0.164 10 B 5.902,1.445 6.362,1.609 0.460,0.164 10 LIN 3.241,1.445 3.575,1.609 0.334,0.164 10 LIN2 0.86,1.445 1.193,1.609 0.334,0.164 10 LIN2 1.308,1.571 1.642,1.735 0.334,0.164 10 10 2.317,1.571 2.537,1.735 0.220,0.164 10 17 3.69,1.571 4.024,1.735 0.334,0.164 10 16 5.637,1.571 5.760,1.735 0.123,0.164 10 9 5.637,0.646 5.760,0.809 0.123,0.164 10 2 5.637,2.096 5.760,2.259 0.123,0.164 10 1 2.628,1.445 3.088,1.609 0.460,0.164 10 LIN1 5.902,1.978 6.362,2.141 0.460,0.164 10 GND 4.851,0.646 5.686,0.809 0.836,0.164 10 P/W FL*1 0.11,3.535 0.932,3.698 0.822,0.164 10 *2: for RHD 0.11,3.273 0.932,3.437 0.822,0.164 10 *1: for LHD 4.851,0.814 5.686,0.977 0.836,0.164 10 P/W FR*2 5.137,2.826 7.135,2.989 1.998,0.164 10 Power Window Regulator Motor 0.217,2.826 1.258,2.989 1.041,0.164 10 Main Body ECU 2.058,2.639 4.123,2.802 2.065,0.164 10 J12*1, I14*2 5.137,2.639 7.135,2.802 1.998,0.164 10 J5*1, I5*2 0.217,2.639 1.258,2.802 1.041,0.164 10 G59

PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs again.

Result
Result Proceed to
B2321 is output A
B2321 is not output B



A

2.INSPECT FUSE (P/W FL, P/W FR)

B

END

2.INSPECT FUSE (P/W FL, P/W FR)
a.

for LHD:

Remove the P/W FL fuse from the main body ECU.


b.

for RHD:

Remove the P/W FR fuse from the instrument panel junction block RH.


c.

Measure the resistance of the fuse.

Standard resistance:

Below 1 Ω




OK

3.CHECK WIRE HARNESS (POWER WINDOW MOTOR - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

3.CHECK WIRE HARNESS (POWER WINDOW MOTOR - BATTERY AND BODY GROUND)
a.
U188629E02
1.906,1.229 2.167,1.229 false 1.26,1.229 1.542,1.229 false 0.083,0.031 1.417,0.229 1.333,0.198 10 false Wire Harness Side: 0.281,1.729 1.063,1.896 0.781,0.167 10 false *2: for RHD 2.219,1.146 2.354,1.292 0.135,0.146 10 false B 0.885,1.146 1.229,1.292 0.344,0.146 10 false GND 0.333,0.906 0.802,1.083 0.469,0.177 10 false I5 0.313,0.615 0.781,0.792 0.469,0.177 10 false J5 0.281,1.417 1.063,1.594 0.781,0.177 10 false *1: for LHD 0.594,0.604 1.063,0.781 0.469,0.177 10 false *1 0.594,0.906 1.063,1.083 0.469,0.177 10 false *2

Disconnect the J5*1 or I5*2 motor connector.


b.

Measure the voltage and resistance of the wire harness side connector.

Standard voltage:
for LHD
Tester Connection Specified Condition
J5-2 (B) - Body ground 10 to 14 V

for RHD
Tester Connection Specified Condition
I5-2 (B) - Body ground 10 to 14 V


Standard resistance:
for LHD
Tester Connection Specified Condition
J5-1 (GND) - Body ground Below 1 Ω

for RHD
Tester Connection Specified Condition
I5-1 (GND) - Body ground Below 1 Ω




OK

4.CHECK WIRE HARNESS (MASTER SWITCH - POWER WINDOW MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WIRE HARNESS (MASTER SWITCH - POWER WINDOW MOTOR)
a.

Disconnect the J12*1 or I14*2 switch connector.


b.

Disconnect the J5*1 or I5*2 motor connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
for LHD
Tester Connection Specified Condition
J12-16 (LIN2) - J5-9 (LIN) Below 1 Ω
J12-16 (LIN2) or J5-9 (LIN) - Body ground 10 kΩ or higher

for RHD
Tester Connection Specified Condition
I14-16 (LIN2) - I5-9 (LIN) Below 1 Ω
I14-16 (LIN2) or I5-9 (LIN) - Body ground 10 kΩ or higher




OK

5.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)
a.

Temporarily replace the power window regulator motor with a new or normally functioning one.



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC

b.

Check for DTCs again.

Result
Result Proceed to
B2321 is not output A
B2321 is output B



A

END (POWER WINDOW REGULATOR MOTOR IS FAULTY)

B

REPLACE MAIN BODY ECU