Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM24M0E _58 Vehicle Interior _059592 WINDOW / GLASS _0292216 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2323  Rear Door RH ECU Communication Stop  


DESCRIPTION

DTC B2323 is output when communication between the power window regulator motor (for rear RH) and main body ECU stops for more than 10 seconds.

DTC No. DTC Detection Condition Trouble Area
B2323 No communication between power window regulator motor (for rear RH) and main body ECU for more than 10 seconds
·

Power window regulator motor (for rear RH)

·

Main body ECU

·

Wire harness



WIRING DIAGRAM

B142470E03
0.759,2.985 1.831,3.132 1.073,0.147 10 G59 5.037,2.985 7.072,3.132 2.036,0.147 10 K2 0.759,3.135 1.831,3.281 1.073,0.147 10 Main Body ECU 5.037,3.135 7.072,3.281 2.036,0.147 10 Power Window Regulator Motor 2.571,0.538 3.364,0.685 0.793,0.147 10 from Battery 4.028,0.678 4.745,0.825 0.716,0.147 10 P/W RR 1.376,1.472 1.707,1.619 0.331,0.147 10 LIN2 1.833,1.594 2.165,1.740 0.331,0.147 10 10 5.364,1.594 5.524,1.740 0.160,0.147 10 9 5.364,0.678 5.524,0.825 0.160,0.147 10 2 5.364,2.453 5.524,2.600 0.160,0.147 10 1 5.598,1.472 5.929,1.619 0.331,0.147 10 LIN 5.598,0.557 5.929,0.704 0.331,0.147 10 B 5.598,2.35 5.929,2.497 0.331,0.147 10 GND

PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs again.

Result
Result Proceed to
B2323 is output A
B2323 is not output B



A

2.INSPECT FUSE (P/W RR)

B

END

2.INSPECT FUSE (P/W RR)
a.

Remove the P/W RR fuse from the instrument panel junction block RH.


b.

Measure the resistance of the fuse.

Standard resistance:

Below 1 Ω




OK

3.CHECK WIRE HARNESS (POWER WINDOW MOTOR - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

3.CHECK WIRE HARNESS (POWER WINDOW MOTOR - BATTERY AND BODY GROUND)
a.
U185949E01
0.036,0.027 1.406,0.192 1.370,0.165 10 Wire Harness Side: 2.19,1.141 2.323,1.292 0.133,0.151 10 B 0.858,1.141 1.198,1.292 0.341,0.151 10 GND 0.326,1.111 0.581,1.292 0.254,0.181 10 K2 1.907,1.213 2.163,1.213 false 1.282,1.213 1.567,1.213 false

Disconnect the K2 motor connector.


b.

Measure the voltage and resistance of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
K2-2 (B) - Body ground 10 to 14 V


Standard resistance:
Tester Connection Specified Condition
K2-1 (GND) - Body ground Below 1 Ω




OK

4.CHECK WIRE HARNESS (MAIN BODY ECU - POWER WINDOW MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WIRE HARNESS (MAIN BODY ECU - POWER WINDOW MOTOR)
a.

Disconnect the G59 ECU connector.


b.

Disconnect the K2 motor connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G59-10 (LIN2) - K2-9 (LIN) Below 1 Ω
G59-10 (LIN2) or K2-9 (LIN) - Body ground 10 kΩ or higher




OK

5.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH)
a.

Temporarily replace the power window regulator motor with a new or normally functioning one.



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC

b.

Check for DTCs again.

Result
Result Proceed to
B2323 is not output A
B2323 is output B



A

END (POWER WINDOW REGULATOR MOTOR IS FAULTY)

B

REPLACE MAIN BODY ECU