Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2014.09
RM24M0E _58 Vehicle Interior _059592 WINDOW / GLASS _0292216 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2311  Power Window Motor Malfunction  


DESCRIPTION

The power window regulator motor is driven by operating the power window switch. The power window regulator motor has motor, regulator and ECU functions.

This DTC is output when the power window regulator motor assembly has a malfunction, or the ECU built into the regulator motor assembly determines that the fully closed window position has deviated approximately 20 mm (0.79 in.) or more from the normal position.

HINT:

This DTC may occur for all the windows.


NOTICE:
·

When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized.

·

After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the AUTO UP function is used. In such cases, the AUTO UP function can be resumed by repeating the following operation at least 5 times:

(a)

Close the power window by fully pulling up the power window switch and holding it in the AUTO UP position.

(b)

Open the power window by fully pushing down the switch.




for Driver side
DTC No. DTC Detection Condition Trouble Area
B2311

When either condition below is met:

(a)

Power window regulator motor malfunctions

(b)

When ECU in power window regulator motor determines that fully closed window position has deviated approx. 20 mm (0.79 in.) or more from normal position



·

Battery disconnection when ignition switch on (IG)

·

Power window regulator motor

·

Incorrect installation of power window components

·

Overheated power window regulator motor



for Front passenger side
DTC No. DTC Detection Condition Trouble Area
B2311

When either condition below is met:

(a)

Power window regulator motor malfunctions

(b)

When ECU in power window regulator motor determines that fully closed window position has deviated approx. 20 mm (0.79 in.) or more from normal position



·

Battery disconnection when ignition switch on (IG)

·

Power window regulator motor

·

Incorrect installation of power window components

·

Overheated power window regulator motor



for Rear LH
DTC No. DTC Detection Condition Trouble Area
B2311

When either condition below is met:

(a)

Power window regulator motor malfunctions

(b)

When ECU in power window regulator motor determines that fully closed window position has deviated approx. 20 mm (0.79 in.) or more from normal position



·

Battery disconnection when ignition switch on (IG)

·

Power window regulator motor

·

Incorrect installation of power window components

·

Overheated power window regulator motor



for Rear RH
DTC No. DTC Detection Condition Trouble Area
B2311

When either condition below is met:

(a)

Power window regulator motor malfunctions

(b)

When ECU in power window regulator motor determines that fully closed window position has deviated approx. 20 mm (0.79 in.) or more from normal position



·

Battery disconnection when ignition switch on (IG)

·

Power window regulator motor

·

Incorrect installation of power window components

·

Overheated power window regulator motor



PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER WINDOW)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and press the intelligent tester main switch ON.


c.

Perform the Active Test according to the prompts displayed on the tester.

NOTICE:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.


Driver side power window regulator motor (Power window ECU)
Item Test Details (Default) Diagnostic Note
Power window UP / OFF (OFF) -
Power window DOWN / OFF (OFF) -

Front passenger side power window regulator motor (Power window ECU)
Item Test Details (Default) Diagnostic Note
Power window UP / OFF (OFF) -
Power window DOWN / OFF (OFF) -

Rear LH power window regulator motor (Power window ECU)
Item Test Details (Default) Diagnostic Note
Power window UP / OFF (OFF) -
Power window DOWN / OFF (OFF) -

Rear RH power window regulator motor (Power window ECU)
Item Test Details (Default) Diagnostic Note
Power window UP / OFF (OFF) -
Power window DOWN / OFF (OFF) -

OK:

Power window operates normally.




OK

2.PERFORM INITIALIZATION

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (APPLICABLE LOCATION)

2.PERFORM INITIALIZATION
a.

Initialize the power window regulator motor assembly (see page Vehicle Interior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).


b.

Check that the power window operates normally by opening and closing the window.

OK:

Power window operates normally.




OK

3.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (APPLICABLE LOCATION)

3.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY
a.

Check that the power window components are installed correctly.

OK:

Power window components are installed correctly.


HINT:

When the power window components are installed correctly, the problem has been caused by battery disconnection while the ignition switch is on (IG), improper installation of the power window components or the motor being overheated.




OK

END

NG

INSTALL PARTS CORRECTLY