Home › Vehicle Interior › WINDOW / GLASS › FRONT SIDE FIX WINDOW GLASS
RM24M0E _58 Vehicle Interior _059592 WINDOW / GLASS _0292228 FRONT SIDE FIX WINDOW GLASS A

WINDOW / GLASS  FRONT SIDE FIX WINDOW GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the LH side and RH side.

·

The procedures listed below are for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 62120A 1.INSTALL FRONT SIDE FIX WINDOW ASSEMBLY LH

a.
B457205E01
2.031,0.958 2.188,0.958 2.188,0.958 2.375,1.125 false 1.531,2.313 2.26,2.313 false 1.948,1.875 2.073,1.875 2.073,1.875 2.333,2.177 false 2.521,0.729 3.302,0.979 0.781,0.25 10 true CORRECT 1.417,0.875 2.135,1.135 0.719,0.26 10 false Primer M 0.896,2.208 1.615,2.479 0.719,0.271 10 false Adhesive 2.135,2.406 3.021,2.688 0.885,0.281 10 false INCORRECT 1.323,1.792 2.042,2.052 0.719,0.26 10 false Primer M 0.552,4.333 1.271,4.594 0.719,0.26 10 false : Primer M

Using a brush, apply Primer M to the exposed part of the vehicle body.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Do not apply primer to the adhesive.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Using a brush or sponge, apply Primer G to the contact surface of the glass.

B144965E01
3.508,0.951 4.931,1.128 1.422,0.177 10 Adhesive Center Line 3.556,2.246 4.978,2.423 1.422,0.176 10 Adhesive Center Line 5.388,0.949 6.810,1.126 1.422,0.177 10 Adhesive Center Line 1.883,1.167 2.025,1.357 0.142,0.191 10 A 3.405,0.163 3.791,0.353 0.386,0.191 10 A - A 5.31,0.163 5.696,0.353 0.386,0.191 10 B - B 3.425,1.452 3.810,1.642 0.386,0.191 10 C - C 1.658,1.482 1.800,1.673 0.142,0.191 10 A 1.472,1.669 1.614,1.860 0.142,0.191 10 B 1.472,2.065 1.614,2.255 0.142,0.191 10 B 1.049,1.328 1.191,1.519 0.142,0.191 10 C 0.636,1.482 0.778,1.673 0.142,0.191 10 C 2.436,2.376 3.055,2.532 0.619,0.156 10 Primer G 0.04,0.019 0.842,0.254 0.803,0.235 10 Backside: 3.998,0.527 3.998,0.915 false 5.894,0.506 5.894,0.895 false 3.981,1.809 4.051,2.208 4.051,2.208 4.136,1.809 false

HINT:

If primer is applied to an area that is not specified, apply a non-residue solvent to a clean cloth and wipe off the excess primer.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




c.

Apply adhesive to the glass.

B144966E04
0.906,1.854 1.021,2.063 0.115,0.208 10 false b 2.552,1.719 2.667,1.927 0.115,0.208 10 false B 2.729,1.521 2.844,1.729 0.115,0.208 10 false A 2.917,1.125 3.031,1.333 0.115,0.208 10 false A 4.188,0.229 4.542,0.438 0.354,0.208 10 false A - A 4.188,1.51 4.542,1.719 0.354,0.208 10 false C - C 5.688,0.229 6.052,0.438 0.365,0.208 10 false B - B 1.906,0.823 2.083,1.031 0.177,0.208 10 true C 1.521,0.958 1.635,1.167 0.115,0.208 10 false C 2.563,2.115 2.677,2.323 0.115,0.208 10 false B 0.365,1.26 0.479,1.469 0.115,0.208 10 false b 0.552,2.313 0.667,2.521 0.115,0.208 10 false a 0.802,1.531 0.917,1.74 0.115,0.208 10 false a 4.188,2.229 5.625,2.438 1.438,0.208 10 false Adhesive Center Line 1.229,2.385 1.865,2.594 0.635,0.208 10 false Adhesive 4.188,0.927 5.625,1.135 1.438,0.208 10 false Adhesive Center Line 5.677,0.927 7.115,1.135 1.438,0.208 10 false Adhesive Center Line 0.042,0.01 0.781,0.24 0.74,0.229 10 true Backside:

Adhesive:

Toyota Genuine Windshield Glass Adhesive or Equivalent


i.

Cut off the tip of the cartridge nozzle as shown in the illustration.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage time frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the glass as shown in the illustration.

Standard measurement:
Area Specified Condition
a 8.0 mm (0.315 in.)
b 6.0 mm (0.236 in.)




d.

Install the front side fix window to the vehicle body.

i.

Hold the front side fix window securely in place with protective tape or equivalent until the adhesive hardens.

NOTICE:
·

Check that the fastener is attached to the vehicle body correctly.

·

Check that the vehicle body and glass have a small gap between them.




ii.

Lightly press the front surface of the glass to ensure that the glass is securely fit to the vehicle body.

NOTICE:

Do not drive the vehicle for the amount of time written in the table below.


Minimum time:
Temperature Minimum time prior to driving vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




Hide 62212 2.INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

Hide 62212 3.INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

Hide 62226 4.INSTALL FRONT PILLAR GARNISH LOWER LH

Hide 75546 5.INSTALL WINDSHIELD OUTSIDE MOULDING CLIP

a.

Install the windshield outside moulding clip (See page Vehicle Interior>EXTERIOR>FRONT PILLAR UPPER COVER>INSTALLATION).


Hide 75534 6.INSTALL WINDSHIELD MOULDING OUTSIDE LH

Hide 68131 7.CHECK FOR LEAKS AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.