53155D
1.REMOVE NO. 1 RADIATOR GRILLE SEAL
Disengage the 2 clips and remove the No. 1 radiator grille seal.
| *1 | Double-sided Tape |
53145B
2.REMOVE RADIATOR GRILLE GARNISH CLIP
Remove the 2 radiator grille garnish clips.
75311
3.REMOVE RADIATOR GRILLE (OR FRONT PANEL) EMBLEM
Disengage the 3 claws and 2 guides and remove the radiator grille (or front panel) emblem.
53152A
4.REMOVE RADIATOR GRILLE AIR GUIDE
Remove the 3 screws.
Disengage the 3 claws and remove the radiator grille air guide.
53115B
5.REMOVE RADIATOR GRILLE BRACKET
Disengage the 14 claws and remove the outer radiator grille.
Disengage the 2 claws and remove the radiator grille bracket.
89348D
6.REMOVE ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)
89341A
7.REMOVE NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89348
8.REMOVE NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
81220
9.REMOVE FOG LIGHT ASSEMBLY LH
81210A
10.REMOVE FOG LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
82114
11.REMOVE NO. 4 ENGINE ROOM WIRE
Disengage the 11 clamps and remove the No. 4 engine room wire.
52040
12.REMOVE FRONT BUMPER HOLE COVER ASSEMBLY LH
Remove the 3 clips.
Disengage the 4 claws and 2 guides and remove the front bumper hole cover assembly LH.
52030
13.REMOVE FRONT BUMPER HOLE COVER ASSEMBLY RH
Use the same procedure as for the LH side.
53155G
14.REMOVE RADIATOR GRILLE SEAL
Remove the radiator grille seal.
Use the same procedure for the RH side and LH side.
52128B
15.REMOVE FRONT BUMPER HOLE COVER LH
Disengage the 4 claws.
| *1 | Hook |
Disengage the hook to remove the front bumper hole cover LH.
52127D
16.REMOVE FRONT BUMPER HOLE COVER RH
Use the same procedure as for the LH side.
52128C
17.REMOVE FRONT BUMPER HOLE COVER LH
Disengage the 4 claws and remove the front bumper hole cover LH.
52127C
18.REMOVE FRONT BUMPER HOLE COVER
Use the same procedure as for the LH side.
53112E
19.REMOVE NO. 1 LOWER RADIATOR GRILLE
Disengage the 16 claws and remove the No. 1 lower radiator grille.
52711
20.REMOVE FRONT BUMPER MOULDING
Disengage the 12 claws and remove the front bumper moulding.
53879A
21.REMOVE FRONT FENDER LINER RETAINER
Disengage the claw and remove the front fender liner retainer.
Use the same procedure for the RH side and LH side.
52116A
22.REMOVE FRONT BUMPER SIDE SUPPORT LH
Remove the 2 screws.
Disengage the 2 claws and remove the front bumper side support LH.
52115A
23.REMOVE FRONT BUMPER SIDE SUPPORT RH
Use the same procedure as for the LH side.
86520
24.REMOVE LOW PITCHED HORN ASSEMBLY
86510
25.REMOVE HIGH PITCHED HORN ASSEMBLY
52611
26.REMOVE FRONT BUMPER ENERGY ABSORBER
Disengage the 4 guides to remove the front bumper energy absorber.
52021
27.REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
Remove the bolt.
Remove the 8 bolts and front bumper reinforcement sub-assembly.