52021
1.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
Install the 8 bolts.
Install the front bumper reinforcement sub-assembly with the bolt.
Engage the 4 clamps.
52611
2.INSTALL FRONT BUMPER ENERGY ABSORBER
Engage the 4 guides to install the front bumper energy absorber.
86520
3.INSTALL LOW PITCHED HORN ASSEMBLY
86510
4.INSTALL HIGH PITCHED HORN ASSEMBLY
52544
5.INSTALL FRONT BUMPER SIDE SEAL LH
Engage the 2 claws to install the front bumper side seal LH.
52543
6.INSTALL FRONT BUMPER SIDE SEAL RH
Use the same procedure as for the LH side.
52116A
7.INSTALL FRONT BUMPER SIDE SUPPORT LH
Engage the claw.
Engage the clip as shown in the illustration.
Install the front bumper side support LH with the screw.
52115A
8.INSTALL FRONT BUMPER SIDE SUPPORT RH
Use the same procedure as for the LH side.
53112E
9.INSTALL NO. 1 LOWER RADIATOR GRILLE
Engage the 17 claws to install the No. 1 lower radiator grille.
Engage the 22 claws.
Install the lower radiator grille sub-assembly with the 3 screws.
53152B
10.INSTALL RADIATOR GRILLE AIR GUIDE
Engage the 4 claws.
Install the radiator grille air guide with the 4 screws.
75311
11.INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM
Engage the 3 claws to install the radiator grille (or front panel) emblem.
53145B
12.INSTALL RADIATOR GRILLE GARNISH CLIP
Install 2 new radiator grille garnish clips.
53155D
13.INSTALL NO. 1 RADIATOR GRILLE SEAL
Clean the radiator grille.
Remove any remaining double-sided tape from the radiator grille.
Wipe off any tape adhesive residue with cleaner.
Remove the release paper from a new No. 1 radiator grille seal.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Engage the 2 clips and install the No. 1 radiator grille seal as shown in the illustration.
| *a | Double-sided Tape |
Press the No. 1 radiator grille seal firmly to install it.
53101
14.INSTALL RADIATOR GRILLE SUB-ASSEMBLY
Engage the 6 claws.
Install the radiator grille sub-assembly with the 2 screws.
53115B
15.INSTALL RADIATOR GRILLE BRACKET
Engage the 4 claws.
Install the radiator grille bracket with the 3 screws.
52040
16.INSTALL FRONT BUMPER HOLE COVER ASSEMBLY LH
Engage the hook.
| *a | Hook |
Engage the 4 claws to install the front bumper hole cover assembly LH.
52030
17.INSTALL FRONT BUMPER HOLE COVER ASSEMBLY RH
Use the same procedure as for the LH side.
82114
18.INSTALL NO. 4 ENGINE ROOM WIRE (w/o Clearance Sonar System)
Engage the 9 clamps to install the No. 4 engine room wire.
82114
19.INSTALL NO. 4 ENGINE ROOM WIRE (w/ Clearance Sonar System)
Engage the 9 clamps to install the No. 4 engine room wire.
89341K
20.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ Clearance Sonar System)
52113D
21.INSTALL FRONT BUMPER EXTENSION LH
Engage the 2 claws to install the front bumper extension LH.
52112D
22.INSTALL FRONT BUMPER EXTENSION RH
Use the same procedure as for the LH side.
8122A
23.INSTALL LED ILLUMINATION LIGHT LH
8121A
24.INSTALL LED ILLUMINATION LIGHT RH
Use the same procedure as for the LH side.
53155G
25.INSTALL RADIATOR GRILLE SEAL
Use the same procedure for the RH side and LH side.
Clean the front bumper cover.
Remove any remaining double-sided tape from the front bumper cover.
Wipe off any tape adhesive residue with cleaner.
Remove the release paper from a new radiator grille seal.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the radiator grille seal as shown in the illustration.
| *a | Double-sided Tape |
Press the radiator grille seal firmly to install it.
53879A
26.INSTALL FRONT FENDER LINER RETAINER
Engage the 2 claws to install the 2 front fender liner retainers.
Use the same procedure for the RH side and LH side.