Home › Engine / Hybrid System › 2AZ-FE STARTING › SMART ENTRY AND START SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292080 SMART ENTRY AND START SYSTEM C

2AZ-FE STARTING  SMART ENTRY AND START SYSTEM  B2284  Brake Signal Malfunction  


DESCRIPTION

HINT:

When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.

After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.


DTC No. DTC Detection Condition Trouble Area
B2284 The brake signal circuit between the main body ECU and the stop light switch is malfunctioning and the CAN information is inconsistent
·

Stop light switch

·

CAN communication system

·

ECM

·

Instrument panel junction block LH (Main body ECU)

·

Wire harness or connector



WIRING DIAGRAM

B157546E08
4.424,0.835 4.554,1.002 0.130,0.166 10 7 5.69,0.953 5.885,1.119 0.195,0.166 10 23 5.958,1.063 6.311,1.229 0.352,0.166 10 STP 3.633,1.551 5.868,1.720 2.235,0.169 10 Instrument Panel Junction Block LH 3.875,2.003 4.707,2.169 0.832,0.166 10 From Battery 4.156,3.519 4.988,3.685 0.832,0.166 10 From Battery 4.38,1.055 4.580,1.217 0.200,0.162 10 4K 5.971,5.758 6.308,5.930 0.338,0.172 10 CAN 5.873,7.188 6.899,7.359 1.026,0.170 10 Main Body ECU 3.806,5.947 4.440,6.105 0.634,0.158 10 CAN Line 0.912,5.76 1.240,5.922 0.328,0.162 10 CAN 0.642,6.871 0.970,7.033 0.328,0.162 10 ECM 1.772,3.864 2.934,4.178 1.162,0.314 10 Instrument Panel Junction Block RH 1.496,3.517 1.694,3.680 0.198,0.162 10 5K 2.988,3.517 3.207,3.680 0.219,0.162 10 5M 2.167,3.656 2.576,3.802 0.408,0.146 10 STOP 1.555,3.302 1.661,3.460 0.106,0.158 10 4 3.039,3.302 3.145,3.460 0.106,0.158 10 1 2.174,2.374 2.461,2.536 0.287,0.162 10 A33 2.174,2.549 3.268,2.711 1.094,0.162 10 Stop Light Switch 1.169,1.999 1.698,2.157 0.529,0.158 10 To ECM 2.138,1.892 2.252,2.063 0.114,0.170 10 4 3.172,1.892 3.286,2.063 0.114,0.170 10 3 3.172,0.94 3.286,1.110 0.114,0.170 10 1 2.126,0.94 2.240,1.110 0.114,0.170 10 2

CAUTION / NOTICE / HINT

EMERGENCY ENGINE START CONTROL


a.

If there is a malfunction in the stop light switch or STOP fuse, their signals may not be correctly transmitted to the main body ECU. This may result in the engine not starting even if the engine switch is pressed while the brake pedal is depressed and the shift lever is in the P position.

To activate the starter:

i.

Turn the engine switch from off to on (ACC).


ii.

Press and hold the engine switch for 15 seconds.




HINT:

Before performing the inspection, depress the brake pedal and check that the stop lights come on. If the stop lights do not come on when the brake pedal is depressed, refer to the page shown in the brackets (See page Vehicle Interior>LIGHTING>LIGHTING SYSTEM(except LED Headlight)>PROBLEM SYMPTOMS TABLE).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Check the DATA LIST for proper functioning of the stop light switch.

Body:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch/ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-

OK:

ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen.




OK

2.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)

NG

4.INSPECT FUSE (STOP)
2.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)

b.

Check for CAN communication system DTCs (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

HINT:

If the DTCs for the CAN communication system malfunction are output, inspect those DTCs first (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).


OK:

No DTC is output.




OK

3.CHECK DTC OUTPUT (ENGINE CONTROL SYSTEM)

NG

3.CHECK DTC OUTPUT (ENGINE CONTROL SYSTEM)

b.

Check for DTC P0500 (Vehicle speed sensor A) (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0500).

OK:

No DTC is output.




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

NG

4.INSPECT FUSE (STOP)
a.

Remove the STOP fuse from the instrument panel junction block RH.


b.

Measure the resistance of the fuse.

Standard resistance:

Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (STOP FUSE - STOP LIGHT SWITCH)

NG

REPLACE FUSE

5.CHECK HARNESS AND CONNECTOR (STOP FUSE - STOP LIGHT SWITCH)
a.
U189910E01
0.299,0 2.641,0.312 2.341,0.312 10 Front view of wire harness connector: (to Stop Light Switch) 0.57,1.392 0.963,1.531 0.393,0.139 10 A33

Disconnect the A33 switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
A33-2 - Body ground Always 11 to 14 V




OK

6.INSPECT STOP LIGHT SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT STOP LIGHT SWITCH
a.
U188844E01
0.095,0.087 2.776,0.424 2.681,0.336 10 Component without harness connected: (Stop Light Switch) 0.265,2.545 0.782,2.868 0.517,0.323 10 Not Pushed 2.539,1.347 2.838,1.488 0.299,0.141 10 A33 1.263,2.597 1.780,2.739 0.517,0.142 10 Pushed

Remove the stop light switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch pin free Below 1 Ω
3 - 4 Switch pin free 10 kΩ or higher
1 - 2 Switch pin pushed in 10 kΩ or higher
3 - 4 Switch pin pushed in Below 1 Ω




OK

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - MAIN BODY ECU)

NG

REPLACE STOP LIGHT SWITCH

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - MAIN BODY ECU)
a.
B460084E01
0.5,1.417 0.917,1.667 0.417,0.25 0.5,3.833 0.917,4.083 0.417,0.25 0.115,0.052 2.385,0.5 2.271,0.448 10 false Front view of wire harness connector: (to Stop Light Switch) 0.563,1.458 1,1.708 0.438,0.25 10 false A33 0.615,3.865 1.052,4.115 0.438,0.25 10 false 4K 0.146,2.594 2.563,2.99 2.417,0.396 10 false Front view of wire harness connector: (to Instrument Panel Junction Block LH)

Disconnect 4K connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A33-1 - 4K-7 Always Below 1 Ω
A33-1 - Body ground 11 kΩ or higher




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR