2011-2016 FJ Cruiser · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Jul 2007


1. INSTALL REAR DISC
  1. Align the matchmarks of the disc and axle hub and install the disc.

    NOTICE:
    When replacing the disc, select the position that gives the minimum disc runout.


2. INSTALL REAR DISC BRAKE CYLINDER HOLE PLUG
  1. Install a new hole plug onto the disc brake cylinder mounting.


3. INSTALL REAR DISC BRAKE BUSH DUST BOOT
  1. Apply lithium soap base glycol grease to a new dust boot.

  1. Install the dust boot onto the disc brake cylinder mounting.


4. INSTALL REAR DISC BRAKE CYLINDER SLIDE BUSH
  1. Apply lithium soap base glycol grease to a new slide bush.

  1. Install the slide bush onto the disc brake cylinder mounting.


5. INSTALL REAR DISC BRAKE CYLINDER MOUNTING

F043126
  1. Install the disc brake cylinder mounting with the 2 bolts and 2 washers.

    Torque:
    105 N*m{ 1,071 kgf*cm , 78 ft.*lbf }


6. INSTALL REAR DISC BRAKE PAD SUPPORT PLATE
  1. Install the 4 pad support plates onto the disc brake cylinder mounting.


7. INSTALL REAR DISC BRAKE PAD WEAR INDICATOR PLATE
  1. Install the indicator plate onto the inner side brake pad.

    HINT:
    Install the indicator plate facing downward.


8. INSTALL REAR DISC BRAKE ANTI SQUEAL SHIM

NOTICE:
If necessary, replace the anti squeal shim when replacing the brake pad.

  1. Install the 2 anti squeal shims onto the brake pads.


9. INSTALL REAR DISC BRAKE PAD
  1. Install the 2 disc brake pads with anti squeal shims onto the disc brake cylinder mounting.

    NOTICE:
    There should be no oil or grease on the friction surfaces of the disc brake pads or the rear disc.


10. INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY
  1. Apply lithium soap base glycol grease to the 2 slide pins.

  1. F043124
    Install the disc brake cylinder onto the disc brake cylinder mounting with the 2 slide pins.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }


11. INSTALL REAR FLEXIBLE HOSE

F043125
  1. Install the rear flexible hose with a new rear flexible hose union bolt and a new gasket.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }


12. BLEED BRAKE LINE
  1. Turn the ignition switch to ON.

  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid until the fluid level is between the MIN and MAX lines of the reservoir.

  1. Repeatedly depress the brake pedal and bleed air from the bleeder plug of the front disc brake cylinder RH.

  1. Repeat the step above until the air is completely bled, and then tighten the bleeder plug while depressing the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.

  1. With the brake pedal depressed, loosen the bleeder plug of the rear disc brake cylinder RH, continue to hold the brake pedal and allow brake fluid to be drained from the bleeder plug while the pump motor operates.

    HINT:
    1. Air is bled as the pump motor operates while the brake pedal is being depressed.
    2. Be sure to release the brake pedal to stop the motor after approximately 100 seconds of continuous operation.
    3. As brake fluid is continuously drained while the pump operates, it is not necessary to repeatedly depress the brake pedal.

  1. When there is no more air in the brake fluid, tighten the bleeder plug, and then release the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the rear disc brake cylinder LH using the same procedure as for the RH side.

  1. Turn the ignition switch off.

  1. Inspect for brake fluid leaks.

  1. Check and adjust the brake fluid level (Click here).

  1. Clear the DTCs (Click here).


13. INSTALL REAR WHEEL

Torque:
112 N*m{ 1,137 kgf*cm , 82 ft.*lbf }

← REASSEMBLY (from Jul 2007)COMPONENTS (from Jul 2007) →