2011-2016 FJ Cruiser · Service Manual ENGINE

TERMINALS OF ECM

System information · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014

A121603E03

HINT:
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated.
The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the STD Voltages column.
The illustration above can be used as a reference to identify the ECM terminal locations.

Symbols (Terminal No.)
Wiring Colors
Terminal Descriptions
Conditions
STD Voltages
BATT (E47-3) - E1 (B3-1)
L - BR
Battery (for measuring the battery voltage and for the ECM memory)
Always
11 to 14 V
+BM (E47-7) - E1 (B3-1)
GR - BR
Power source of throttle motor
Always
11 to 14 V
IGSW (E47-9) - E1 (B3-1)
B-O - BR
Ignition switch
Ignition switch ON
11 to 14 V
+B (E47-1) - E1 (B3-1)
B - BR
Power source of ECM
Ignition switch ON
11 to 14 V
+B2 (E47-2) - E1 (B3-1)
B - BR
Power source of ECM
Ignition switch ON
11 to 14 V
OC1+ (B3-17) - OC1- (B3-16)
G-Y - L-B
Camshaft timing oil control valve (OCV)
Ignition switch ON
Pulse generation
(see waveform 1)
OC2+ (B3-15) - OC2- (B3-14)
L-W - L-R
Camshaft timing oil control valve (OCV)
Ignition switch ON
Pulse generation
(see waveform 1)
MREL (E47-8) - E1 (B3-1)
W-G - BR
EFI relay
Ignition switch ON
11 to 14 V
VC (B1-23) - E2 (B1-28)
L-R - W-G
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
VG (B1-30) - E2G (B1-29)
R - R-W
Mass air flow meter
Idling, Transmission gear neutral, A/C switch OFF
0.5 to 3.0 V
THA (B1-22) - E2 (B1-28)
R-B - W-G
Intake air temperature sensor
Idling, Intake air temperature 20°C (68°F)
0.5 to 3.4 V
THW (B1-21) - E2 (B1-28)
B - W-G
Engine coolant temperature sensor
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
VTA1 (B1-20) - E2 (B1-28)
G-B - W-G
Throttle position sensor (for engine control)
Ignition switch ON, Throttle valve fully closed
0.5 to 1.2 V
Ignition switch ON, Throttle valve fully open
3.2 to 4.8 V
VTA2 (B1-19) - E2 (B1-28)
G-W - W-G
Throttle position sensor (for sensor malfunction detection)
Ignition switch ON, Throttle valve fully closed
2.1 to 3.1 V
Ignition switch ON, Throttle valve fully open
4.5 to 5.0 V
VPA (E47-18) - EPA (E47-20)
W-R - LG-B
Accelerator pedal position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON, Accelerator pedal fully depressed
2.6 to 4.5 V
VPA2 (E47-19) - EPA2 (E47-21)
R-B - V-W
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
1.2 to 2.0 V
Ignition switch ON, Accelerator pedal fully depressed
3.4 to 5.0 V
VCPA (E47-26) - EPA (E47-20)
B-Y - LG-B
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.5 V
VCP2 (E47-27) - EPA2 (E47-21)
W-L - V-W
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.5 V
HA1A (B2-2) - E04 (B2-7)
R-L - W-B
A/F sensor heater
Idling, after warming up
Pulse generation
(see waveform 2)
HA2A (B2-1) - E05 (B2-6)
B-W - W-B
Ignition switch ON
11 to 14 V
A1A+ (B2-22) - E1 (B3-1)
P - BR
A/F sensor
Ignition switch ON
3.3 V*1
A2A+ (B2-23) - E1 (B3-1)
Y - BR
A/F sensor
Ignition switch ON
3.3 V*1
A1A- (B2-30) - E1 (B3-1)
L - BR
A/F sensor
Ignition switch ON
2.9 V*1
A2A- (B2-31) - E1 (B3-1)
BR - BR
A/F sensor
Ignition switch ON
2.9 V*1
HT1B (B1-1) - E1 (B3-1)
G - BR
Heated oxygen sensor heater
Idling
Below 3.0 V
HT2B (B2-5) - E1 (B3-1)
L - BR
Ignition switch ON
11 to 14 V
OX1B (B1-18) - E2 (B1-28)
W - W-G
Heated oxygen sensor
Maintain engine speed at 2,500 rpm for 2 minutes after warming up
Pulse generation
(see waveform 3)
OX2B (B2-33) - E2 (B1-28)
B - W-G
#10 (B3-2) - E01 (B1-7)
R-L - BR
Fuel injector
Ignition switch ON
11 to 14 V
#20 (B3-3) - E01 (B1-7)
G - BR
#30 (B3-4) - E01 (B1-7)
R - BR
#40 (B3-5) - E01 (B1-7)
W - BR
Idling
Pulse generation
(see waveform 4)
#50 (B3-6) - E01 (B1-7)
Y - BR
#60 (B3-7) - E01 (B1-7)
L - BR
KNK1 (B2-29) - EKNK (B2-28)
B - W
Knock sensor
Maintain engine speed at 4,000 rpm after warming up
Pulse generation
(see waveform 5)
KNK2 (B2-21) - EKN2 (B2-20)
G - R
Knock sensor
Maintain engine speed at 4,000 rpm after warming up
Pulse generation
(see waveform 5)
VV1+ (B3-19) - VV1- (B3-29)
R - G
Variable Valve Timing (VVT) sensor
Idling
Pulse generation
(see waveform 6)
VV2+ (B3-18) - VV2- (B3-28)
Y - L
Variable Valve Timing (VVT) sensor
Idling
Pulse generation
(see waveform 6)
NE+ (B3-21) - NE- (B3-20)
B - W
Crankshaft position sensor
Idling
Pulse generation
(see waveform 6)
IGT1 (B1-8) - E1 (B3-1)
Y-R - BR
Ignition coil assembly (ignition signal)
Idling
Pulse generation
(see waveform 7)
IGT2 (B1-9) - E1 (B3-1)
G - BR
IGT3 (B1-10) - E1 (B3-1)
B-W - BR
IGT4 (B1-11) - E1 (B3-1)
Y-G - BR
IGT5 (B1-12) - E1 (B3-1)
GR - BR
IGT6 (B1-13) - E1 (B3-1)
L - BR
IGF1 (B1-24) - E1 (B3-1)
W-R - BR
Ignition coil assembly (ignition confirmation signal)
Ignition switch ON
4.5 to 5.5 V
Idling
Pulse generation
(see waveform 7)
PRG (B1-34) - E01 (B1-7)
G-Y - BR
Purge VSV
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(see waveform 8)
SPD (E46-8) - E1 (B3-1)
V-R - BR
Speed signal from combination meter
Ignition switch ON, Rotate driving wheel slowly
Pulse generation
(see waveform 9)
STA (B3-11) - E1 (B3-1)
B-Y - BR
Starter signal
Cranking
11 to 14 V
STP (E47-15) - E1 (B3-1)
G-Y - BR
Stop light switch
Brake pedal depressed
7.5 to 14 V
Brake pedal released
Below 1.5 V
ST1- (E47-16) - E1 (B3-1)
R-L - BR
Stop light switch (opposite to STP terminal)
Ignition switch ON, Brake pedal depressed
Below 1.5 V
Ignition switch ON, Brake pedal released
7.5 to 14 V
NSW (B2-8) - E1 (B3-1)
L-Y - BR
Park/Neutral position switch (for automatic transmission)
Ignition switch ON, Shift lever position in P or N
Below 3.0 V
Ignition switch ON, Shift lever position other than P and N
11 to 14 V
M+ (B1-5) - ME01 (B2-3)
P - W-B
Throttle motor
Idling with warm engine
Pulse generation
(see waveform 10)
M- (B1-4) - ME01 (B2-3)
L - W-B
Throttle motor
Idling with warm engine
Pulse generation
(see waveform 11)
FC (E47-10) - E1 (B3-1)
GR-B - BR
Fuel pump control
Ignition switch ON
11 to 14 V
FPR (B3-30) - E1 (B3-1)
Y-B - BR
Fuel pump control
Engine cranking
11 to 14 V
Engine idling
Below 3.0 V
W (E46-30) - E1 (B3-1)
R-B - BR
MIL
Ignition switch ON
Below 3.0 V
Idling
11 to 14 V
ELS (E46-13) - E1 (B3-1)
Y-B - BR
Electric load
Defogger or taillight switch OFF
0 to 1.5 V
Defogger or taillight switch ON
7.5 to 14 V
TC (E47-23) - E1 (B3-1)
P-L - BR
Terminal TC of DLC 3
Ignition switch ON
11 to 14 V
TACH (E46-1) - E1 (B3-1)
B-W - BR
Engine speed
Idling
Pulse generation
(see waveform 12)
ACIS (B1-33) - E1 (B3-1)
W-L - BR
VSV for ACIS
Ignition switch ON
11 to 14 V
PSW (B3-10) - E1 (B3-1)
G-W - BR
P/S pressure switch
Ignition switch ON
11 to 14 V
F/PS (E46-32) - E1 (B3-1)
L - BR
Airbag sensor assembly
Idling with warm engine
Pulse generation
(see waveform 13)
CANH (E46-33) - E1 (B3-1)
W - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 14)
CANL (E46-34) - E1 (B3-1)
R - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 15)
*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

WAVEFORM 1
A093229E26
Camshaft timing oil control valve (OCV) 
ECM Terminal Names
Between OC1+ and OC1- or OC2+ and OC2-
Tester Ranges
5 V/DIV, 1 msec./DIV
Conditions
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 2
A151305E02
A/F sensor heater 
ECM Terminal Names
CH1: Between HA1A and E04
CH2: Between HA2A and E05
Tester Ranges
5 V/DIV, 10 msec./DIV
Conditions
Idling with warm engine, 10 seconds or more after start engine

WAVEFORM 3
A088863E29
Heated oxygen sensor 
ECM Terminal Names
Between OX1B and E2 or OX2B and E2
Tester Ranges
0.2 V/DIV, 200 msec./DIV
Conditions
Engine speed maintained at 2,500 rpm for 2 minutes after warming up sensor

HINT:
In the DATA LIST, item O2S B1S2 or O2S B2S2 shows the ECM input values from the heated oxygen sensor.


WAVEFORM 4
G035622E08
Fuel injector 
ECM Terminal Names
Between #10 (to 60) and E01
Tester Ranges
20 V/DIV, 20 msec./DIV
Conditions
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 5
A085286E46
Knock sensor 
ECM Terminal Names
Between KNK1 and EKNK or KNK2 and EKN2
Tester Ranges
500 mV/DIV, 0.01 to 1 msec./DIV
Conditions
Engine speed maintained at 4,000 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as the engine rpm increases.
  2. The waveforms and amplitudes displayed on the tester differ slightly depending on the vehicle.


WAVEFORM 6
G035795E30
  1. VVT sensor

  2. Crankshaft position sensor

    ECM Terminal Names
    (a) Between NE+ and NE-
    (b) Between VV1+ and VV1- or VV2+ and VV2-
    Tester Ranges
    2 V/DIV, 20 msec./DIV
    Conditions
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 7
G035664E10
  1. Igniter IGT signal (from ECM to igniter)

  2. Igniter IGF signal (from igniter to ECM)

    ECM Terminal Names
    (a) Between IGT (1 to 6) and E1
    (b) Between IGF1 and E1
    Tester Ranges 2
    2 V/DIV, 20 msec./DIV
    Conditions
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 8
A116415E04
Purge VSV 
ECM Terminal Names
Between PRG and E01
Tester Ranges
10 V/DIV, 50 msec./DIV
Conditions
Idling

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 9
A093224E24
Vehicle speed signal 
ECM Terminal Names
Between SPD and E1
Tester Ranges
2 V/DIV, 20 msec./DIV
Conditions
Driving at 20 km/h (12 mph)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 10
A093274E26
Throttle actuator positive terminal 
ECM Terminal Names
Between M+ and ME01
Tester Ranges
5 V/DIV, 1 msec./DIV
Conditions
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 11
A093275E27
Throttle actuator negative terminal 
ECM Terminal Names
Between M- and ME01
Tester Ranges
5 V/DIV, 1 msec./DIV
Conditions
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 12
A093225E27
Engine speed signal 
ECM Terminal Names
Between TACH and E1
Tester Ranges
5 V/DIV, 10 msec./DIV
Conditions
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 13
A093227E10
Airbag sensor assembly 
ECM Terminal Names
Between F/PS and E1
Tester Ranges
5 V/DIV, 500 msec./DIV
Conditions
Idling with warm engine

WAVEFORM 14
A086154E28
CAN communication signal (Reference) 
ECM Terminal Names
Between CANH and E1
Tester Ranges
1 V/DIV, 10μsec./DIV
Conditions
Ignition switch ON

HINT:
The wavelength varies depending on the CAN communication signal.


WAVEFORM 15
A086155E29
CAN communication signal (Reference) 
ECM Terminal Names
Between CANL and E1
Tester Ranges
1 V/DIV, 10μsec./DIV
Conditions
Ignition switch ON

HINT:
The wavelength varies depending on the CAN communication signal.

← PROBLEM SYMPTOMS TABLE (from Aug 2014)TERMINALS OF ECM (Aug 2009 – Oct 2010) →