2011-2016 FJ Cruiser · Service Manual ENGINE

TERMINALS OF ECM

System information · Vehicles built Aug 2012 – Jul 2014

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014

A227797E01

HINT:
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.

Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E82-24 (BATT) - B49-12 (E1)
L - BR
Battery (for measuring the battery voltage and for the ECM memory)
Always
11 to 14 V
B49-23 (+BM) - B49-12 (E1)
R-G - BR
Power source of throttle motor
Always
11 to 14 V
E81-21 (IGSW) - B49-12 (E1)
B-O - BR
Ignition switch
Ignition switch ON
11 to 14 V
E82-22 (+B) - B49-12 (E1)
B - BR
Power source of ECM
Ignition switch ON
11 to 14 V
E82-23 (+B2) - B49-12 (E1)
B - BR
Power source of ECM
Ignition switch ON
11 to 14 V
B48-19 (OC1+) - B48-20 (OC1-)
G-Y - L-B
Camshaft timing oil control valve (OCV) (for intake side of bank 1)
Idling
Pulse generation
(see waveform 1)
B47-19 (OC2+) - B47-20 (OC2-)
L-W - L-R
Camshaft timing oil control valve (OCV) (for intake side of bank 2)
Idling
Pulse generation
(see waveform 1)
B48-21 (OE1+) - B48-22 (OE1-)
G-B - B-R
Camshaft timing oil control valve (OCV) (for exhaust side of bank 1)
Idling
Pulse generation
(see waveform 1)
B47-21 (OE2+) - B47-22 (OE2-)
B-W - R-L
Camshaft timing oil control valve (OCV) (for exhaust side of bank 2)
Idling
Pulse generation
(see waveform 1)
E82-9 (MREL) - B49-12 (E1)
W-G - BR
EFI relay
Ignition switch ON
11 to 14 V
B47-15 (VCV1) - B48-8 (ETHW)
P-L - W-R
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
B47-16 (VCV2) - B48-8 (ETHW)
LG-B - W-R
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
B48-14 (VG) - B48-13 (E2G)
G - B-Y
Mass air flow meter
Idling, Shift lever position P or N, A/C switch OFF
0.5 to 3.0 V
B48-15 (THA) - B48-7 (ETHA)
P - W-G
Intake air temperature sensor
Idling, Intake air temperature 20°C (68°F)
0.5 to 3.4 V
B49-17 (THW) - B48-8 (ETHW)
B - W-R
Engine coolant temperature sensor
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
B49-15 (VTA1) - B49-14 (ETA)
B-L - W
Throttle position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON, Accelerator pedal fully depressed
3.2 to 4.8 V
B49-16 (VTA2) - B49-14 (ETA)
G-W - W
Throttle position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
2.1 to 3.1 V
Ignition switch ON, Accelerator pedal fully depressed
4.6 to 5.0 V
E81-6 (VPA) - E81-3 (EPA)
W-R - LG-B
Accelerator pedal position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON, Accelerator pedal fully depressed
2.6 to 4.5 V
E81-5 (VPA2) - E81-1 (EPA2)
R-B - V-W
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
1.2 to 2.0 V
Ignition switch ON, Accelerator pedal fully depressed
3.4 to 4.75 V
E81-4 (VCPA) - E81-3 (EPA)
G - LG-B
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.5 V
E81-2 (VCP2) - E81-1 (EPA2)
W-L - V-W
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.5 V
B49-13 (VCTA) - B49-14 (ETA)
R - W
Power source of throttle position sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
B50-17 (HA1A) - B50-16 (E04)
B50-19 (HA2A) - B50-18 (E05)
R-L - W-B
B-W - W-B
Air fuel ratio sensor heater
Idling with warm engine
Pulse generation
(see waveform 2)
Ignition switch ON
11 to 14 V
B49-1 (A1A+) - B49-12 (E1)
R - BR
Air fuel ratio sensor
Ignition switch ON
3.3 V*1
B49-7 (A2A+) - B49-12 (E1)
Y - BR
Air fuel ratio sensor
Ignition switch ON
3.3 V*1
B49-2 (A1A-) - B49-12 (E1)
G - BR
Air fuel ratio sensor
Ignition switch ON
2.9 V*1
B49-8 (A2A-) - B49-12 (E1)
L - BR
Air fuel ratio sensor
Ignition switch ON
2.9 V*1
B50-12 (HT1B) - B50-11 (E03)
B50-13 (HT2B) - B50-11 (E03)
B - W-B
GR - W-B
Heated oxygen sensor heater
Idling
Below 3.0 V
Ignition switch ON
11 to 14 V
B47-2 (OX1B) - B47-1 (EX1B)
B47-4 (OX2B) - B47-3 (EX2B)
W - B
P - L
Heated oxygen sensor
Maintain engine speed at 2500 rpm for 2 minutes after warming up sensor
Pulse generation
(see waveform 3)
B50-6 (#10) - B50-14 (E01)
B50-1 (#20) - B50-14 (E01)
B50-7 (#30) - B50-14 (E01)
B50-2 (#40) - B50-14 (E01)
B50-8 (#50) - B50-14 (E01)
B50-3 (#60) - B50-14 (E01)
R-L - BR
G - BR
R - BR
W - BR
Y - BR
L - BR
Fuel injector
Ignition switch ON
11 to 14 V
B50-6 (#10) - B50-14 (E01)
B50-1 (#20) - B50-14 (E01)
B50-7 (#30) - B50-14 (E01)
B50-2 (#40) - B50-14 (E01)
B50-8 (#50) - B50-14 (E01)
B50-3 (#60) - B50-14 (E01)
R-L - BR
G - BR
R - BR
W - BR
Y - BR
L - BR
Fuel injector
Idling
Pulse generation
(see waveform 4)
B48-11 (KNK1) - B48-12 (EKNK)
B - W
Knock sensor
Maintain engine speed at 4000 rpm after warming up
Pulse generation
(see waveform 5)
B48-5 (KNK2) - B48-6 (EKN2)
G - R
Knock sensor
Maintain engine speed at 4000 rpm after warming up
Pulse generation
(see waveform 5)
B47-9 (VV1+) - B47-10 (VV1-)
R - G
Variable Valve Timing (VVT) sensor (for intake side of bank 1)
Idling
Pulse generation
(see waveform 6)
B47-12 (VV2+) - B47-11 (VV2-)
Y - L
Variable Valve Timing (VVT) sensor (for intake side of bank 2)
Idling
Pulse generation
(see waveform 6)
B47-13 (EV1+) - B47-14 (EV1-)
B-Y - R-B
Variable Valve Timing (VVT) sensor (for exhaust side of bank 1)
Idling
Pulse generation
(see waveform 7)
B47-18 (EV2+) - B47-17 (EV2-)
GR - P
Variable Valve Timing (VVT) sensor (for exhaust side of bank 2)
Idling
Pulse generation
(see waveform 7)
B47-6 (NE+) - B47-5 (NE-)
B - W
Crankshaft position sensor
Idling
Pulse generation
(see waveform 6)
B49-24 (IGT1) - B49-12 (E1)
B49-25 (IGT2) - B49-12 (E1)
B49-26 (IGT3) - B49-12 (E1)
B49-27 (IGT4) - B49-12 (E1)
B49-28 (IGT5) - B49-12 (E1)
B48-25 (IGT6) - B49-12 (E1)
Y-R - BR
G - BR
B-W - BR
Y-G - BR
GR - BR
L - BR
Ignition coil with igniter (ignition signal)
Idling
Pulse generation
(see waveform 8)
B49-6 (IGF1) - B49-12 (E1)
W-R - BR
Ignition coil with igniter (ignition confirmation signal)
Ignition switch ON
4.5 to 5.5 V
Idling
Pulse generation
(see waveform 8)
B49-18 (PRG) - B49-12 (E1)
G-Y - BR
Purge VSV
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(see waveform 9)
E82-18 (SPD) - B49-12 (E1)
V-R - BR
Speed signal from combination meter
Driving at 20 km/h (12 mph)
Pulse generation
(see waveform 10)
E81-10 (STA) - B49-12 (E1)
V-R - BR
Starter signal
Cranking
11 to 14 V
E81-18 (STP) - B49-12 (E1)
G-Y - BR
Stop light switch
Brake pedal depressed
7.5 to 14 V
Brake pedal released
Below 1.5 V
E82-8 (ST1-) - B49-12 (E1)
R-L - BR
Stop light switch (opposite to STP terminal)
Ignition switch ON, Brake pedal depressed
Below 1.5 V
Ignition switch ON, Brake pedal released
7.5 to 14 V
B48-2 (NSW) - B49-12 (E1)
L-Y - BR
Park/Neutral position switch (for automatic transmission)
Ignition switch ON, Shift lever position in P or N
Below 3.0 V
Ignition switch ON, Shift lever position other than P and N
11 to 14 V
B50-20 (M+) - B50-10 (ME01)
P - W-B
Throttle motor
Idling with warm engine
Pulse generation
(see waveform 11)
B49-29 (M-) - B50-10 (ME01)
L - W-B
Throttle motor
Idling with warm engine
Pulse generation
(see waveform 12)
E82-3 (FPC) - B49-12 (E1)
G - BR
Fuel pump control
Ignition switch ON
11 to 14 V
E81-8 (FC) - B49-12 (E1)
GR-B - BR
Fuel pump control
Ignition switch ON
11 to 14 V
E82-13 (W) - B49-12 (E1)
R-B - BR
MIL
Ignition switch ON
Below 3.0 V
Idling
11 to 14 V
E82-11 (ELS1) - B49-12 (E1)
Y-B - BR
Electric load
Defogger switch OFF
0 to 1.5 V
Defogger switch ON
7.5 to 14 V
E81-28 (TC) - B49-12 (E1)
P-L - BR
Terminal TC of DLC 3
Ignition switch ON
11 to 14 V
E81-29 (TACH) - B49-12 (E1)
B-W - BR
Engine speed
Idling
Pulse generation
(see waveform 13)
B48-16 (PSP) - B49-12 (E1)
V - BR
P/S pressure switch (sensor)
Ignition switch ON
0.5 to 4.5 V
E81-26 (DI) - B49-12 (E1)
GR - BR
Fuel pump control
Ignition switch ON
0 to 3.0 V
B48-28 (ALT) - B49-12 (E1)
W-L - BR
Generator
Ignition switch ON
11 to 14 V
E81-32 (CANH) - B49-12 (E1)
LG-R - BR
CAN communication line
Stop engine and ignition switch to ON
Pulse generation
(see waveform 14)
E81-31 (CANL) - B49-12 (E1)
LG-B - BR
CAN communication line
Stop engine and ignition switch to ON
Pulse generation
(see waveform 15)
*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

WAVEFORM 1
A093229E42
Camshaft Timing Oil Control Valve (OCV) 
ECM Terminal Name
Between OC1+ and OC1- or OC2+ and OC2-
OE1+ and OE1- or OE2+ and OE2-
Tester Range
5 V/DIV, 1 msec./DIV
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 2
A172534E01
Air Fuel Ratio Sensor Heater 
ECM Terminal Name
CH1: Between HA1A and E04
CH2: Between HA2A and E05
Tester Range
5 V/DIV, 10 msec./DIV
Condition
Idling with warm engine

HINT:
The wavelength varies in accordance with the engine operating condition.


WAVEFORM 3
A088863E56
Heated Oxygen Sensor 
ECM Terminal Name
Between OX1B and EX1B or OX2B and EX2B
Tester Range
200 mV/DIV, 200 msec./DIV
Condition
Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

HINT:
In the Data List, item O2S B1 S2 or O2S B2 S2 shows the ECM input values from the heated oxygen sensor.


WAVEFORM 4
G035622E17
Fuel Injector 
ECM Terminal Name
Between #10 (to 60) and E01
Tester Range
20 V/DIV, 20 msec./DIV
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 5
A085286E72
Knock Sensor 
ECM Terminal Name
Between KNK1 and EKNK or KNK2 and EKN2
Tester Range
1 V/DIV, 1 msec./DIV
Condition
Engine speed maintained at 4000 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as the engine speed increases.
  2. The waveforms and amplitudes displayed on the tester differ slightly depending on the vehicle.


WAVEFORM 6
A122767E04
Crankshaft Position Sensor and VVT Sensor for Intake Camshaft 
ECM Terminal Name
(a) Between NE+ and NE-
(b) Between VV1+ and VV1- or VV2+ and VV2-
Tester Range
5 V/DIV, 20 msec./DIV
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 7
A122768E04
VVT Sensor for Exhaust Camshaft 
ECM Terminal Name
Between EV1+ and EV1- or EV2+ and EV2-
Tester Range
5 V/DIV, 20 msec./DIV
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 8
G035664E12
Igniter IGT Signal (from ECM to Igniter) and Igniter IGF Signal (from Igniter to ECM) 
ECM Terminal Name
(a) Between IGT (1 to 6) and E1
(b) Between IGF1 and E1
Tester Ranges 2
2 V/DIV, 20 msec./DIV
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 9
A228042E01
Purge VSV 
ECM Terminal Name
Between PRG and E1
Tester Range
10 V/DIV, 50 msec./DIV
Condition
Idling, under purge control

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 10
A093224E30
Vehicle Speed Signal 
ECM Terminal Name
Between SPD and E1
Tester Range
2 V/DIV, 20 msec./DIV
Condition
Driving at 20 km/h (12 mph)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 11
A208000E09
Throttle Actuator Positive Terminal 
ECM Terminal Name
Between M+ and ME01
Tester Range
5 V/DIV, 1 msec./DIV
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 12
A245848E09
Throttle Actuator Negative Terminal 
ECM Terminal Name
Between M- and ME01
Tester Range
5 V/DIV, 1 msec./DIV
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 13
A093225E37
Engine Speed Signal 
ECM Terminal Name
Between TACH and E1
Tester Range
5 V/DIV, 10 msec./DIV
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 14
A086154E01
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANH and E1
Tester Range
1 V/DIV, 10 μsec./DIV
Condition
Stop engine and ignition switch to ON

HINT:
The wavelength varies depending on the CAN communication signal.


WAVEFORM 15
A086155E48
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANL and E1
Tester Range
1 V/DIV, 10 μsec./DIV
Condition
Stop engine and ignition switch to ON

HINT:
The wavelength varies depending on the CAN communication signal.

← TERMINALS OF ECM (Aug 2011 – Jul 2012)TERMINALS OF ECM (from Aug 2014) →