TERMINALS OF ECM
System information · Vehicles built Nov 2010 – Jul 2011
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014


- HINT:
- The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.
| Terminal No. (Symbol) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| E82-24 (BATT) - B49-12 (E1) |
L - BR |
Battery (for measuring the battery voltage and for the ECM memory) |
Always |
11 to 14 V |
| B49-23 (+BM) - B49-12 (E1) |
R-G - BR |
Power source of throttle motor |
Always |
11 to 14 V |
| E81-21 (IGSW) - B49-12 (E1) |
B-O - BR |
Ignition switch |
Ignition switch ON |
11 to 14 V |
| E82-22 (+B) - B49-12 (E1) |
B - BR |
Power source of ECM |
Ignition switch ON |
11 to 14 V |
| E82-23 (+B2) - B49-12 (E1) |
B - BR |
Power source of ECM |
Ignition switch ON |
11 to 14 V |
| B48-19 (OC1+) - B48-20 (OC1-) |
G-Y - L-B |
Camshaft timing oil control valve (OCV) (for intake side of bank 1) |
Idling |
Pulse generation (see waveform 1) |
| B47-19 (OC2+) - B47-20 (OC2-) |
L-W - L-R |
Camshaft timing oil control valve (OCV) (for intake side of bank 2) |
Idling |
Pulse generation (see waveform 1) |
| B48-21 (OE1+) - B48-22 (OE1-) |
G-B - B-R |
Camshaft timing oil control valve (OCV) (for exhaust side of bank 1) |
Idling |
Pulse generation (see waveform 1) |
| B47-21 (OE2+) - B47-22 (OE2-) |
B-W - R-L |
Camshaft timing oil control valve (OCV) (for exhaust side of bank 2) |
Idling |
Pulse generation (see waveform 1) |
| E82-9 (MREL) - B49-12 (E1) |
W-G - BR |
EFI relay |
Ignition switch ON |
11 to 14 V |
| B47-15 (VCV1) - B48-8 (ETHW) |
P-L - W-R |
Power source of sensor (specific voltage) |
Ignition switch ON |
4.5 to 5.5 V |
| B47-16 (VCV2) - B48-8 (ETHW) |
LG-B - W-R |
Power source of sensor (specific voltage) |
Ignition switch ON |
4.5 to 5.5 V |
| B48-14 (VG) - B48-13 (E2G) |
G - B-Y |
Mass air flow meter |
Idling, Shift lever position P or N, A/C switch OFF |
0.5 to 3.0 V |
| B48-15 (THA) - B48-7 (ETHA) |
P - W-G |
Intake air temperature sensor |
Idling, Intake air temperature 20°C (68°F) |
0.5 to 3.4 V |
| B49-17 (THW) - B48-8 (ETHW) |
B - W-R |
Engine coolant temperature sensor |
Idling, Engine coolant temperature 80°C (176°F) |
0.2 to 1.0 V |
| B49-15 (VTA1) - B49-14 (ETA) |
B-L - W |
Throttle position sensor (for engine control) |
Ignition switch ON, Accelerator pedal fully released |
0.5 to 1.1 V |
| Ignition switch ON, Accelerator pedal fully depressed |
3.2 to 4.8 V |
|||
| B49-16 (VTA2) - B49-14 (ETA) |
G-W - W |
Throttle position sensor (for sensor malfunction detection) |
Ignition switch ON, Accelerator pedal fully released |
2.1 to 3.1 V |
| Ignition switch ON, Accelerator pedal fully depressed |
4.6 to 5.0 V |
|||
| E81-6 (VPA) - E81-3 (EPA) |
W-R - LG-B |
Accelerator pedal position sensor (for engine control) |
Ignition switch ON, Accelerator pedal fully released |
0.5 to 1.1 V |
| Ignition switch ON, Accelerator pedal fully depressed |
2.6 to 4.5 V |
|||
| E81-5 (VPA2) - E81-1 (EPA2) |
R-B - V-W |
Accelerator pedal position sensor (for sensor malfunction detection) |
Ignition switch ON, Accelerator pedal fully released |
1.2 to 2.0 V |
| Ignition switch ON, Accelerator pedal fully depressed |
3.4 to 5.0 V |
|||
| E81-4 (VCPA) - E81-3 (EPA) |
G - LG-B |
Power source of accelerator pedal position sensor (for VPA) |
Ignition switch ON |
4.5 to 5.5 V |
| E81-2 (VCP2) - E81-1 (EPA2) |
W-L - V-W |
Power source of accelerator pedal position sensor (for VPA2) |
Ignition switch ON |
4.5 to 5.5 V |
| B50-17 (HA1A) - B50-16 (E04) B50-19 (HA2A) - B50-18 (E05) |
R-L - W-B B-W - W-B |
A/F sensor heater |
Idling with warm engine |
Pulse generation (see waveform 2) |
| Ignition switch ON |
11 to 14 V |
|||
| B49-1 (A1A+) - B49-12 (E1) |
R - BR |
A/F sensor |
Ignition switch ON |
3.3 V*1 |
| B49-7 (A2A+) - B49-12 (E1) |
Y - BR |
A/F sensor |
Ignition switch ON |
3.3 V*1 |
| B49-2 (A1A-) - B49-12 (E1) |
G - BR |
A/F sensor |
Ignition switch ON |
2.9 V*1 |
| B49-8 (A2A-) - B49-12 (E1) |
L - BR |
A/F sensor |
Ignition switch ON |
2.9 V*1 |
| B50-12 (HT1B) - B50-11 (E03) B50-13 (HT2B) - B50-11 (E03) |
B - W-B GR - W-B |
Heated oxygen sensor heater |
Idling |
Below 3.0 V |
| Ignition switch ON |
11 to 14 V |
|||
| B47-2 (OX1B) - B47-1 (EX1B) B47-4 (OX2B) - B47-3 (EX2B) |
W - W-G B - B-R |
Heated oxygen sensor |
Maintain engine speed at 2500 rpm for 2 minutes after warming up sensor |
Pulse generation (see waveform 3) |
| B50-6 (#10) - B50-14 (E01) B50-1 (#20) - B50-14 (E01) B50-7 (#30) - B50-14 (E01) B50-2 (#40) - B50-14 (E01) B50-8 (#50) - B50-14 (E01) B50-3 (#60) - B50-14 (E01) |
R-L - BR G - BR R - BR W - BR Y - BR L - BR |
Fuel injector |
Ignition switch ON |
11 to 14 V |
| B50-6 (#10) - B50-14 (E01) B50-1 (#20) - B50-14 (E01) B50-7 (#30) - B50-14 (E01) B50-2 (#40) - B50-14 (E01) B50-8 (#50) - B50-14 (E01) B50-3 (#60) - B50-14 (E01) |
R-L - BR G - BR R - BR W - BR Y - BR L - BR |
Fuel injector |
Idling |
Pulse generation (see waveform 4) |
| B48-11 (KNK1) - B48-12 (EKNK) |
B - W |
Knock sensor |
Maintain engine speed at 4000 rpm after warming up |
Pulse generation (see waveform 5) |
| B48-5 (KNK2) - B48-6 (EKN2) |
G - R |
Knock sensor |
Maintain engine speed at 4000 rpm after warming up |
Pulse generation (see waveform 5) |
| B47-9 (VV1+) - B47-10 (VV1-) |
R - G |
Variable Valve Timing (VVT) sensor (for intake side of bank 1) |
Idling |
Pulse generation (see waveform 6) |
| B47-12 (VV2+) - B47-11 (VV2-) |
Y - L |
Variable Valve Timing (VVT) sensor (for intake side of bank 2) |
Idling |
Pulse generation (see waveform 6) |
| B47-13 (EV1+) - B47-14 (EV1-) |
B-Y - R-B |
Variable Valve Timing (VVT) sensor (for exhaust side of bank 1) |
Idling |
Pulse generation (see waveform 7) |
| B47-18 (EV2+) - B47-17 (EV2-) |
GR - P |
Variable Valve Timing (VVT) sensor (for exhaust side of bank 2) |
Idling |
Pulse generation (see waveform 7) |
| B47-6 (NE+) - B47-5 (NE-) |
B - W |
Crankshaft position sensor |
Idling |
Pulse generation (see waveform 6) |
| B49-24 (IGT1) - B49-12 (E1) B49-25 (IGT2) - B49-12 (E1) B49-26 (IGT3) - B49-12 (E1) B49-27 (IGT4) - B49-12 (E1) B49-28 (IGT5) - B49-12 (E1) B48-25 (IGT6) - B49-12 (E1) |
Y-R - BR G - BR B-W - BR Y-G - BR GR - BR L - BR |
Ignition coil with igniter (ignition signal) |
Idling |
Pulse generation (see waveform 8) |
| B49-6 (IGF1) - B49-12 (E1) |
W-R - BR |
Ignition coil with igniter (ignition confirmation signal) |
Ignition switch ON |
4.5 to 5.5 V |
| Idling |
Pulse generation (see waveform 8) |
|||
| B49-18 (PRG) - B49-12 (E1) |
G-Y - BR |
Purge VSV |
Ignition switch ON |
11 to 14 V |
| Idling |
Pulse generation (see waveform 9) |
|||
| E82-18 (SPD) - B49-12 (E1) |
V-R - BR |
Speed signal from combination meter |
Driving at 20 km/h (12 mph) |
Pulse generation (see waveform 10) |
| E81-10 (STA) - B49-12 (E1) |
V-R - BR |
Starter signal |
Cranking |
11 to 14 V |
| E81-18 (STP) - B49-12 (E1) |
G-Y - BR |
Stop light switch |
Brake pedal depressed |
7.5 to 14 V |
| Brake pedal released |
Below 1.5 V |
|||
| E82-8 (ST1-) - B49-12 (E1) |
R-L - BR |
Stop light switch (opposite to STP terminal) |
Ignition switch ON, Brake pedal depressed |
Below 1.5 V |
| Ignition switch ON, Brake pedal released |
7.5 to 14 V |
|||
| B48-2 (NSW) - B49-12 (E1) |
L-Y - BR |
Park/Neutral position switch (for automatic transmission) |
Ignition switch ON, Shift lever position in P or N |
Below 3.0 V |
| Ignition switch ON, Shift lever position other than P and N |
11 to 14 V |
|||
| B50-20 (M+) - B50-10 (ME01) |
P - W-B |
Throttle motor |
Idling with warm engine |
Pulse generation (see waveform 11) |
| B49-29 (M-) - B50-10 (ME01) |
L - W-B |
Throttle motor |
Idling with warm engine |
Pulse generation (see waveform 12) |
| E82-3 (FPC) - B49-12 (E1) |
G - BR |
Fuel pump control |
Ignition switch ON |
11 to 14 V |
| E81-8 (FC) - B49-12 (E1) |
GR-B - BR |
Fuel pump control |
Ignition switch ON |
11 to 14 V |
| E82-13 (W) - B49-12 (E1) |
R-B - BR |
MIL |
Ignition switch ON |
Below 3.0 V |
| Idling |
11 to 14 V |
|||
| E82-11 (ELS1) - B49-12 (E1) |
Y-B - BR |
Electric load |
Defogger switch OFF |
0 to 1.5 V |
| Defogger switch ON |
7.5 to 14 V |
|||
| E81-28 (TC) - B49-12 (E1) |
P-L - BR |
Terminal TC of DLC 3 |
Ignition switch ON |
11 to 14 V |
| E81-29 (TACH) - B49-12 (E1) |
B-W - BR |
Engine speed |
Idling |
Pulse generation (see waveform 13) |
| B48-16 (PSP) - B49-12 (E1) |
V - BR |
P/S pressure switch (sensor) |
Ignition switch ON |
0.5 to 4.5 V |
| E82-17 (F/PS) - B49-12 (E1) |
L-O - BR |
Airbag sensor assembly |
Idling with warm engine |
Pulse generation (see waveform 14) |
| E81-32 (CANH) - B49-12 (E1) |
LG-R - BR |
CAN communication line |
Stop engine and ignition switch to ON |
Pulse generation (see waveform 15) |
| E81-31 (CANL) - B49-12 (E1) |
LG-B - BR |
CAN communication line |
Stop engine and ignition switch to ON |
Pulse generation (see waveform 16) |
| WAVEFORM 1 |
![]() ![]() |
| ECM Terminal Name |
Between OC1+ and OC1- or OC2+ and OC2- OE1+ and OE1- or OE2+ and OE2- |
| Tester Range |
5 V/DIV, 1 msec./DIV |
| Condition |
Idling |
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
| WAVEFORM 2 |
![]() ![]() |
| ECM Terminal Name |
CH1: Between HA1A and E04 CH2: Between HA2A and E05 |
| Tester Range |
5 V/DIV, 10 msec./DIV |
| Condition |
Idling with warm engine |
- HINT:
- The wavelength varies in accordance with the engine operating condition.
| WAVEFORM 3 |
![]() ![]() |
| ECM Terminal Name |
Between OX1B and EX1B or OX2B and EX2B |
| Tester Range |
0.2 V/DIV, 200 msec./DIV |
| Condition |
Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor |
- HINT:
- In the Data List, item O2S B1 S2 or O2S B2 S2 shows the ECM input values from the heated oxygen sensor.
| WAVEFORM 4 |
![]() ![]() |
| ECM Terminal Name |
Between #10 (to 60) and E01 |
| Tester Range |
20 V/DIV, 20 msec./DIV |
| Condition |
Idling |
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
| WAVEFORM 5 |
![]() ![]() |
| ECM Terminal Name |
Between KNK1 and EKNK or KNK2 and EKN2 |
| Tester Range |
1 V/DIV, 1 msec./DIV |
| Condition |
Engine speed maintained at 4000 rpm after warming up engine |
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
- The waveforms and amplitudes displayed on the tester differ slightly depending on the vehicle.
- The wavelength becomes shorter as the engine rpm increases.
| WAVEFORM 6 |
![]() ![]() |
| ECM Terminal Name |
(a) Between NE+ and NE- (b) Between VV1+ and VV1- or VV2+ and VV2- |
| Tester Range |
5 V/DIV, 20 msec./DIV |
| Condition |
Idling |
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
| WAVEFORM 7 |
![]() ![]() |
| ECM Terminal Name |
Between EV1+ and EV1- or EV2+ and EV2- |
| Tester Range |
5 V/DIV, 20 msec./DIV |
| Condition |
Idling |
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
| WAVEFORM 8 |
![]() ![]() |
| ECM Terminal Name |
(a) Between IGT (1 to 6) and E1 (b) Between IGF1 and E1 |
| Tester Ranges 2 |
2 V/DIV, 20 msec./DIV |
| Condition |
Idling |
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
| WAVEFORM 9 |
![]() ![]() |
| ECM Terminal Name |
Between PRG and E1 |
| Tester Range |
10 V/DIV, 50 msec./DIV |
| Condition |
Idling, under purge control |
- HINT:
- If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.
| WAVEFORM 10 |
![]() ![]() |
| ECM Terminal Name |
Between SPD and E1 |
| Tester Range |
2 V/DIV, 20 msec./DIV |
| Condition |
Driving at 20 km/h (12 mph) |
- HINT:
- The wavelength becomes shorter as the vehicle speed increases.
| WAVEFORM 11 |
![]() ![]() |
| ECM Terminal Name |
Between M+ and ME01 |
| Tester Range |
5 V/DIV, 1 msec./DIV |
| Condition |
Idling with warm engine |
- HINT:
- The duty ratio varies depending on the throttle actuator operation.
| WAVEFORM 12 |
![]() ![]() |
| ECM Terminal Name |
Between M- and ME01 |
| Tester Range |
5 V/DIV, 1 msec./DIV |
| Condition |
Idling with warm engine |
- HINT:
- The duty ratio varies depending on the throttle actuator operation.
| WAVEFORM 13 |
![]() ![]() |
| ECM Terminal Name |
Between TACH and E1 |
| Tester Range |
5 V/DIV, 10 msec./DIV |
| Condition |
Idling |
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
| WAVEFORM 14 |
![]() ![]() |
| ECM Terminal Name |
Between F/PS and E1 |
| Tester Range |
5 V/DIV, 500 msec./DIV |
| Condition |
Idling with warm engine |
| WAVEFORM 15 |
![]() ![]() |
| ECM Terminal Name |
Between CANH and E1 |
| Tester Range |
1 V/DIV, 10 μsec./DIV |
| Condition |
Stop engine and ignition switch to ON |
- HINT:
- The wavelength varies depending on the CAN communication signal.
| WAVEFORM 16 |
![]() ![]() |
| ECM Terminal Name |
Between CANL and E1 |
| Tester Range |
1 V/DIV, 10 μsec./DIV |
| Condition |
Stop engine and ignition switch to ON |
- HINT:
- The wavelength varies depending on the CAN communication signal.















