P2102 Throttle Actuator Control Motor Circuit Low
Diagnostic trouble codes · Vehicles built from Aug 2009
Also covers:
- P2103 Throttle Actuator Control Motor Circuit High
Versions by build date: Jul 2007 – Jul 2009 from Aug 2009
DESCRIPTION
The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.The opening angle of the throttle valve is detected by the Throttle Position (TP) sensor, which is mounted on the throttle body with motor assembly. The TP sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.
- HINT:
- This ETCS (Electronic Throttle Control System) does not use a throttle cable.
DTC No.
DTC Detection Condition
Trouble Area
P2102
Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic):
(a) Throttle actuator duty ratio 80% or more
(b) Throttle actuator current less than 0.5 A
- Open in throttle actuator circuit
- Throttle actuator (throttle with motor body assembly)
- ECM
P2103
Either of following conditions met (1 trip detection logic): - Hybrid IC diagnosis signal failure
- Hybrid IC current limiter port failure
- Short in throttle actuator circuit
- Throttle actuator (throttle with motor body assembly)
- Throttle valve
- Throttle with motor body assembly
- ECM
- Open in throttle actuator circuit
MONITOR DESCRIPTION
The ECM monitors the electrical current through the electronic actuator, and detects malfunctions and open circuits in the throttle actuator (throttle body with motor assembly) based on this value. If the current is outside the standard range, the ECM determines that there is a malfunction in the throttle actuator. In addition, if the throttle valve does not function properly (for example, stuck on), the ECM determines that there is a malfunction. The ECM then illuminates the MIL and stores a DTC.Example:
When the electrical current is less than 0.5 A and the throttle actuator duty ratio exceeds 80%, the ECM interprets this as the current being outside the standard range, and illuminates the MIL and stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored when the engine is quickly revved to a high rpm several times after the engine is started and has idled for 5 seconds.
FAIL-SAFE
When either of these DTCs, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Duty (Open) /Throttle Motor Duty (Close)) can be read using the intelligent tester. However, the ECM shuts off the throttle actuator current when the ETCS malfunctions.
- The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Duty (Open) /Throttle Motor Duty (Close)) can be read using the intelligent tester. However, the ECM shuts off the throttle actuator current when the ETCS malfunctions.
| 1. INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR) |
![]() ![]() |
Disconnect the throttle with motor body assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
2 (M+) - 1 (M-)
20°C (68°F)
0.3 to 100 Ω
Text in Illustration *1
Component without harness connected
(Throttle With Motor Body Assembly)
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (THROTTLE ACTUATOR - ECM) |
Disconnect the throttle with motor body assembly connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B14-2 (M+) - B50-20 (M+)
Always
Below 1 Ω
B14-1 (M-) - B49-29 (M-)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B14-2 (M+) or B50-20 (M+) - Body ground
Always
10 kΩ or higher
B14-1 (M-) or B49-29 (M-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE) |
Check for foreign objects between the throttle valve and the housing.
- OK:
- No foreign objects between throttle valve and housing.
|
|
||||
| OK | |
| 4. INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE) |
Check if the throttle valve opens and closes smoothly.
- OK:
- Throttle valve opens and closes smoothly.
|
|
||||
| OK | ||
| ||

