2011-2016 FJ Cruiser · Service Manual ENGINE

P2118 Throttle Actuator Control Motor Current Range / Performance

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009

DESCRIPTION

The ETCS (Electronic Throttle Control System) has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (less than 4 V), the ECM determines that there is a malfunction in the ETCS and cuts off the current to the throttle motor.
When the voltage becomes unstable, the ETCS itself becomes unstable. For this reason, when the voltage is low, the current to the throttle motor is cut. If repairs are made and the system returns to normal, turn the ignition switch OFF. The ECM then allows the current to flow to the throttle motor so that it can be restarted.

HINT:
The ETCS does not use a throttle cable.

A115751E04
DTC No.
DTC Detection Conditions
Trouble Areas
P2118
Open in ETCS power source (+BM) circuit (1 trip detection logic)
  1. Open in ETCS power source circuit
  2. ETCS fuse
  3. ECM

MONITOR DESCRIPTION

The ECM monitors the battery supply voltage applied to the throttle motor.
When the power supply voltage (+BM) drops to below 4 V for 0.8 seconds or more, the ECM interprets this as an open in the power supply circuit (+BM). The ECM illuminates the MIL and sets the DTC.
If the malfunction is not repaired successfully, the DTC is set 5 seconds after the engine is next started.

FAIL-SAFE

When this DTC, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, is set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle motor off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned OFF.

WIRING DIAGRAM

A133422E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK FUSE (ETCS FUSE)
A133438E03
  1. Remove the ETCS fuse from the engine room relay block.

  1. Check the ETCS fuse resistance.

    Standard Resistance:
    Below 1 Ω

  1. Reinstall the ETCS fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2. INSPECT ECM (+BM VOLTAGE)
G100798E12
  1. Measure the voltage between the terminals of the B2 and E47 ECM connectors.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    +BM (E47-7) - ME01 (B2-3)
    11 to 14 V



OK
CHECK FOR INTERMITTENT PROBLEMS (Click here)
NG


3. CHECK HARNESS AND CONNECTOR (ECM - ETCS FUSE, ETCS FUSE - BATTERY)
A133448E03
  1. Check the harness and connector between the ETCS fuse and ECM.

    1. Remove the ETCS fuse from the engine room relay block.

    2. Disconnect the E47 ECM connector.

    3. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connections
      Specified Conditions
      ETCS fuse (2) - +BM (E47-7)
      Below 1 Ω

      Standard Resistance (Check for short):
      Tester Connections
      Specified Conditions
      ETCS fuse (2) or +BM (E47-7) - Body ground
      10 kΩ or higher

    4. Reinstall the ETCS fuse.

    5. Reconnect the ECM connector.

  1. Check the harness and connector between the ETCS fuse and positive battery cable.

    1. Remove the ETCS fuse from the engine room relay block.

    2. Disconnect the negative battery cable.

    3. Disconnect the positive battery cable.

    4. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connections
      Specified Conditions
      Positive battery cable - ETCS fuse (1)
      Below 1 Ω

      Standard Resistance (Check for short):
      Tester Connections
      Specified Conditions
      Positive battery cable or ETCS fuse (1) - Body ground
      10 kΩ or higher

    5. Reinstall the ETCS fuse.

    6. Reconnect the positive battery cable.

    7. Reconnect the negative battery cable.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P2111 Throttle Actuator Control System - Stuck Open (+ P2112) (from Aug 2009)P2118 Throttle Actuator Control Motor Current Range / Performance (from Aug 2009) →