2011-2016 FJ Cruiser · Service Manual ENGINE

P2118 Throttle Actuator Control Motor Current Range / Performance

Diagnostic trouble codes · Vehicles built from Aug 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009

DESCRIPTION

The ETCS (Electronic Throttle Control System) has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (less than 4 V), the ECM determines that there is a malfunction in the ETCS and cuts off the current to the throttle actuator.
When the voltage becomes unstable, the ETCS itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the ignition switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.

HINT:
The ETCS does not use a throttle cable.

A112629E48
DTC No.
DTC Detection Condition
Trouble Area
P2118
Open in ETCS power source (+BM) circuit
(1 trip detection logic)
  1. Open in ETCS power source circuit
  2. Battery
  3. Battery terminals
  4. ETCS fuse
  5. ECM

MONITOR DESCRIPTION

The ECM monitors the battery supply voltage applied to the throttle actuator.
When the power supply voltage (+BM) drops below 4 V for 0.8 seconds or more, the ECM interprets this as an open in the power supply circuit (+BM). The ECM illuminates the MIL and stores the DTC.
If the malfunction is not repaired successfully, the DTC is stored 5 seconds after the engine is next started.

FAIL-SAFE

When this DTC or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A185022E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (+BM VOLTAGE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / +BM Voltage.

  1. Read the value displayed on the tester.

    Result 
    Result
    Proceed to
    Less than 11 V or more than 14 V
    A
    11 to 14 V
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)
A226982E04
  1. Disconnect the ECM connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B49-23 (+BM) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B49-12 (E1) - Body ground
    Always
    Below 1 Ω
    B50-10 (ME01) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*1
Rear view of wire harness connector
(to ECM)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P2118 Throttle Actuator Control Motor Current Range / Performance (Jul 2007 – Jul 2009)P2119 Throttle Actuator Control Throttle Body Range / Performance (Jul 2007 – Nov 2007) →