P2119 Throttle Actuator Control Throttle Body Range / Performance
Diagnostic trouble codes · Vehicles built Aug 2009 – Oct 2010
Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010
DESCRIPTION
The Electronic Throttle Control System (ETCS) is composed of the throttle actuator, Throttle Position (TP) sensor, Accelerator Pedal Position (APP) sensor, and ECM. The ECM operates the throttle actuator to regulate the throttle valve in response to driver inputs. The TP sensor detects the opening angle of the throttle valve, and provides the ECM with feedback so that the throttle valve can be appropriately controlled by the ECM.| DTC No. |
DTC Detection Condition |
Trouble Area |
| P2119 |
Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic) |
|
MONITOR DESCRIPTION
The ECM determines the actual opening angle of the throttle valve from the TP sensor signal. The actual opening angle is compared to the target opening angle commanded by the ECM. If the difference between these two values is outside the standard range, the ECM interprets this as a malfunction in the ETCS. The ECM then illuminates the MIL and stores the DTC.If the malfunction is not repaired successfully, the DTC is stored when the accelerator pedal is quickly released (to close the throttle valve) after the engine speed reaches 5000 rpm by the accelerator pedal being fully depressed (fully open the throttle valve).
FAIL-SAFE
When this DTC or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.
WIRING DIAGRAM
Refer to DTC P2102 (Click here).INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2119) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
Result Result
Proceed to
P2119 is output
A
P2119 and other DTCs are output
B
- HINT:
- If any DTCs other than P2119 are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR) |
![]() ![]() |
Disconnect the throttle body with motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
2 (M+) - 1 (M-)
20°C (68°F)
0.3 to 100 Ω
Text in Illustration *1
Component without harness connected
(Throttle With Motor Body Assembly)
|
|
||||
| OK | |
| 3. REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 4. CHECK WHETHER DTC OUTPUT RECURS (DTC P2119) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear DTCs (Click here).
Allow the engine to idle for 15 seconds or more.
Fully depress and release the accelerator pedal several times quickly.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
- OK:
- No DTC is output.
- HINT:
- The output voltage of the throttle position sensor can be checked using the intelligent tester. Variations in the output voltage indicate that the throttle actuator is in operation. To check the output voltage using the intelligent tester, enter the following menus: Powertrain / Engine and ECT / Throttle Position No. 1.
|
|
||||
| OK | ||
| ||


