2011-2016 FJ Cruiser · Service Manual ENGINE

P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Also covers:

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

HINT:
  1. These DTCs relate to the Accelerator Pedal Position (APP) sensor.
  2. This ETCS (Electronic Throttle Control System) does not use a throttle cable.

The Accelerator Pedal Position (APP) sensor is mounted on the accelerator pedal bracket and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type, and uses Hall-effect elements, in order to yield accurate signals, even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0 V and 5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the APP sensor itself.
The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.
A115889E06
DTC No.
DTC Detection Conditions
Trouble Areas
P2120
VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)
  1. Accelerator Pedal Position (APP) sensor (Accelerator pedal rod assembly)
  2. ECM
P2122
VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
  1. APP sensor (Accelerator pedal rod assembly)
  2. Open in VCP1 circuit
  3. Open or ground short in VPA circuit
  4. ECM
P2123
VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic)
  1. APP sensor (Accelerator pedal rod assembly)
  2. Open in EPA circuit
  3. ECM
P2125
VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)
  1. APP sensor (Accelerator pedal rod assembly)
  2. ECM
P2127
VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
  1. APP sensor (Accelerator pedal rod assembly)
  2. Open in VCP2 circuit
  3. Open or ground short in VPA2 circuit
  4. ECM
P2128
Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic)
  1. (a) VPA2 4.8 V or more
  2. (b) VPA between 0.4 V and 3.45 V
  1. APP sensor (Accelerator pedal rod assembly)
  2. Open in EPA2 circuit
  3. ECM
P2138
Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic)
  1. (a) Difference between VPA and VPA2 0.02 V or less
  2. (b) VPA 0.4 V or less and VPA2 1.2 V or less
  1. Short between VPA and VPA2 circuits
  2. APP sensor (Accelerator pedal rod assembly)
  3. ECM

HINT:
When any of these DTCs are set, check the APP sensor voltage by selecting the following menu items on an intelligent tester: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.
Trouble Areas
Accelerator Position No. 1
When Accelerator Pedal Released
Accelerator Position No. 2
When Accelerator Pedal Released
Accelerator Position No. 1
When Accelerator Pedal Depressed
Accelerator Position No. 2
When Accelerator Pedal Depressed
VCP circuit open
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
Open or ground short in VPA circuit
0 to 0.2 V
1.2 to 2.0 V
0 to 0.2 V
3.4 to 5.0 V
Open or ground short in VPA2 circuit
0.5 to 1.1 V
0 to 0.2 V
2.6 to 4.5 V
0 to 0.2 V
EPA circuit open
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
Normal condition
0.5 to 1.1 V
1.2 to 2.0 V
2.6 to 4.5 V
3.4 to 5.0 V


MONITOR DESCRIPTION

When either of the output voltages of VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits is less than the threshold, the ECM determines that there is a malfunction in the APP sensor. The ECM then illuminates the MIL and sets a DTC.
Example:
When the output voltage of VPA drops to below 0.4 V for more than 0.5 seconds when the accelerator pedal is fully depressed, DTC P2122 is set.
If the malfunction is not repaired successfully, a DTC is set 2 seconds after the engine is next started.

FAIL-SAFE

When any of DTCs P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138 are set, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned OFF.

WIRING DIAGRAM

A133490E06

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION NO. 1 AND ACCELERATOR POSITION NO. 2)
FI07052E06
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.

  1. Read the value displayed on the tester.

    Standard Voltage:
    Accelerator Pedal
    Operations
    Accelerator Position No. 1
    Accelerator Position No. 2
    Released
    0.5 to 1.1 V
    1.2 to 2.0 V
    Depressed
    2.6 to 4.5 V
    3.4 to 5.0 V



OK
Go to step 5
NG


2. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
A116156E02
  1. Disconnect the A2 Accelerator Pedal Position (APP) sensor connector.

  1. Disconnect the E47 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    VPA (A2-6) - VPA (E47-18)
    Below 1 Ω
    EPA (A2-5) - EPA (E47-20)
    VCPA (A2-4) - VCPA (E47-26)
    VPA2 (A2-3) - VPA2 (E47-19)
    EPA2 (A2-2) - EPA2 (E47-21)
    VCP2 (A2-1) - VCP2 (E47-27)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    VPA (A2-6) or VPA (E47-18) - Body ground
    10 kΩ or higher
    EPA (A2-5) or EPA (E47-20) - Body ground
    VCPA (A2-4) or VCPA (E47-26) - Body ground
    VPA2 (A2-3) or VPA2 (E47-19) - Body ground
    EPA2 (A2-2) or EPA2 (E47-21) - Body ground
    VCP2 (A2-1) or VCP2 (E47-27) - Body ground

  1. Reconnect the APP sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ECM (VCPA AND VCP2 VOLTAGE)
A116173E03
  1. Disconnect the A2 APP sensor connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the E47 ECM connector.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    VCPA (E47-26) - EPA (E47-20)
    4.5 to 5.5 V
    VCP2 (E47-27) - EPA2 (E47-21)

  1. Reconnect the APP sensor connector.



NG
REPLACE ECM (Click here)
OK


4. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
Replace the accelerator pedal rod assembly (Click here).

NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Fully depress and release the accelerator pedal several times quickly.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138
    A
    No output
    B



B
END
A

REPLACE ECM (Click here)


← P2119 Throttle Actuator Control Throttle Body Range / Performance (from Nov 2010)P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit (+ 6 more codes) (Aug 2009 – Oct 2010) →