2011-2016 FJ Cruiser · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2012 Nov 2012 – Jul 2014 from Aug 2014


1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)

2. DRAIN ENGINE COOLANT

A070279E01

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. Remove the service hole cover from the engine under cover.

  1. Install a vinyl hose onto the drain on the radiator side.

  1. Fix the vinyl hose with tape.

  1. A076320E02
    Loosen the 3 drain plugs on the engine and radiator, and drain the coolant.

  1. Remove the radiator cap.

  1. Drain the coolant from the reservoir tank.

  1. Tighten the 3 drain plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for the engine

  1. Remove the vinyl hose from the radiator.


3. REMOVE V-BANK COVER

A126474
  1. Remove the 2 nuts, then remove the V-bank cover.


4. REMOVE AIR CLEANER ASSEMBLY

A075594E01
  1. Disconnect the No. 2 ventilation hose.

  1. A075595E01
    Disconnect the vacuum hose.

  1. Disconnect the mass air flow meter connector.

  1. Disengage the 2 wire harness clamps.

  1. A075596E01
    Loosen the 2 hose clamps.

  1. Remove the 2 bolts.

  1. Disconnect the air cleaner hose and remove the air cleaner.


5. REMOVE THROTTLE BODY BRACKET

  1. A126392
    Remove the 2 bolts and the throttle body bracket.


6. REMOVE OIL BAFFLE PLATE

  1. A126390
    Remove the bolt and the oil baffle plate.


7. REMOVE NO. 1 SURGE TANK STAY

  1. A126389
    Remove the 2 bolts and the No. 1 surge tank stay.


8. REMOVE NO. 2 SURGE TANK STAY

  1. A126391
    Remove the 2 bolts and the No. 2 surge tank stay.


9. REMOVE INTAKE AIR SURGE TANK

  1. A126395
    Disconnect the 2 water by-pass hoses.

  1. A126449
    Disconnect the fuel vapor feed hose.

  1. A075645
    Disconnect the ventilation hose.

  1. A075646E01
    Disconnect the 2 VSV connectors.

  1. Disconnect the throttle body with motor connector.

  1. Separate the 3 wire harness clamps and the hose clamp.

  1. A075648
    Remove the 2 nuts.

  1. Using a socket hexagon wrench 8, remove the 4 bolts, intake air surge tank and the gasket.


10. DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

A121823E01
  1. Remove the No. 2 fuel pipe clamp.

  1. Pinch the tube connector, and then pull the fuel pipe out of the delivery pipe as shown in the illustration.

    NOTICE:
    1. Remove any dirt and foreign objects from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.


11. DISCONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY

A121824E01
  1. Remove the No. 2 fuel pipe clamp.

  1. Pinch the tube connector, and then pull the fuel pipe out of the delivery pipe as shown in the illustration.

    NOTICE:
    1. Remove any dirt and foreign objects from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.


12. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

A075652E01
  1. Disconnect the 6 fuel injector connectors.

  1. Remove the 6 bolts and remove the fuel delivery pipe together with the 6 fuel injectors.

    NOTICE:
    Do not drop the injectors when removing the fuel delivery pipe.


13. REMOVE FUEL INJECTOR

A075653E05
  1. Pull the 6 injectors out of the delivery pipe.

← COMPONENTS (from Aug 2009)REMOVAL (Aug 2009 – Oct 2012) →